OptiPump HPS Controller Version 2.01 – SCADA Modbus Map – Rev 1.00 – 04/22/2021
Monitors (16-Bit Holding Registers) - Read-Only (0x03)
Address | Description | Scaling | Units | Minimum | Maximum | Values | Notes |
0 | Version Software/Firmware/Program | x | |||||
1 | HOA State | x | 0 = Off 1 = Hand 2 = Auto |
||||
2 | Command Reference (x.xx Hz) | x.xx | Hz | ||||
7 | Index Alarm (Future SD Log) | N/A | N/A | ||||
8 | Index Shutdown (Future SD Log) | N/A | N/A | ||||
9 | Index Fault (Future SD Log) | N/A | N/A | ||||
10 | Raw Analog Input 1 | x | N/A | 0 | 1023 | 1024 = Out of Range | |
11 | Raw Analog Input 2 | x | N/A | 0 | 1023 | 1024 = Out of Range | |
12 | Raw Analog Input 3 | x | N/A | 0 | 1023 | 1024 = Out of Range | |
13 | Raw Analog Input 4 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
14 | Raw Analog Input 5 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
15 | Raw Analog Input 6 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
16 | Raw Analog Input 7 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
17 | Raw Analog Input 8 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
18 | Raw Analog Input 9 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
19 | Raw Analog Input 10 | x.x | DegF | 32767 = Greatly Below/Above Range | |||
20 | Raw Analog Input 11 | x | N/A | 0 | 16383 | -1 = Below Range 16384 = Above Range 32767 = Greatly Below/Above Range |
|
21 | Raw Analog Input 12 | x | N/A | 0 | 4095 | 4096 = Exceeds Range | |
22 | Raw Analog Input 13 | x | N/A | 0 | 4095 | 4097 = Exceeds Range | |
23 | Raw Analog Input 14 | x | N/A | 0 | 4095 | 4098 = Exceeds Range | |
24 | Raw Analog Input 15 | x | N/A | 0 | 4095 | 4099 = Exceeds Range | |
25 | Raw Analog Input 16 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
26 | Raw Analog Input 17 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
27 | Raw Analog Input 18 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
28 | Raw Analog Input 19 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
29 | Raw Analog Input 20 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
30 | Raw Analog Input 21 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
31 | Raw Analog Input 22 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
32 | Raw Analog Input 23 | x.x | DegF | -58.0 | 860.0 | -10000 = Short Circuit 10000 = Open Circuit |
|
33 | Raw (AO1) Pressure Control Valve Position | x | N/A | 0 | 4095 | ||
34 | Raw (AO2) Multipurpose | x | N/A | 0 | 4095 | ||
35 | Scaled Analog Input 1 | x | |||||
36 | Scaled Analog Input 2 | x | |||||
37 | Scaled Analog Input 3 | x.x | |||||
38 | Scaled Analog Input 3 | x.x | PSI | ||||
39 | Scaled Analog Input 4 | x | |||||
40 | Scaled Analog Input 5 | x | |||||
41 | Scaled Analog Input 6 | x.xx | |||||
42 | Scaled Analog Input 7 | x.x | kBPD | ||||
43 | Scaled Analog Input 8 | x.x | |||||
44 | Scaled Analog Input 9 | x.x | % | ||||
45 | Scaled Analog Input 10 | x.x | DegF | -328.0 | 1400.0 | ||
46 | Scaled Analog Input 11 | x.xx | |||||
47 | Scaled Analog Input 12 | x.xx | |||||
48 | Scaled Analog Input 13 | x.xx | |||||
49 | Scaled Analog Input 14 | x.x | |||||
50 | Scaled Analog Input 15 | x.x | |||||
51 | Scaled Analog Input 16 | x.x | DegF | -58.0 | 860.0 | ||
52 | Scaled Analog Input 17 | x.x | DegF | -58.0 | 860.0 | ||
53 | Scaled Analog Input 18 | x.x | DegF | -58.0 | 860.0 | ||
54 | Scaled Analog Input 19 | x.x | DegF | -58.0 | 860.0 | ||
55 | Scaled Analog Input 20 | x.x | DegF | -58.0 | 860.0 | ||
56 | Scaled Analog Input 21 | x.x | DegF | -58.0 | 860.0 | ||
57 | Scaled Analog Input 22 | x.x | DegF | -58.0 | 860.0 | ||
58 | Scaled Analog Input 23 | x.x | DegF | -58.0 | 860.0 | ||
59 | Scaled Filter Differential Pressure | x.x | PSI | ||||
60 | Scaled (AO1) Pressure Control Valve Position | x.x | % | ||||
61 | Scaled (AO2) Multipurpose | x.x | % | ||||
62 | V/mA Analog Input 1 | x.xx | mA | ||||
63 | V/mA Analog Input 2 | x.xx | mA | ||||
64 | V/mA Analog Input 3 | x.xx | mA | ||||
65 | V/mA Analog Input 4 | x.xx | mA | ||||
66 | V/mA Analog Input 5 | x.xx | mA | ||||
67 | V/mA Analog Input 6 | x.xx | mA | ||||
68 | V/mA Analog Input 7 | x.xx | mA | ||||
69 | V/mA Analog Input 8 | x.xx | mA | ||||
70 | V/mA Analog Input 9 | x.xx | mA | ||||
71 | V/mA Analog Input 10 | N/A | N/A | Temperature input. Always 0. | |||
72 | V/mA Analog Input 11 | x.xx | mA | ||||
73 | V/mA Analog Input 12 | x.xx | mA | ||||
74 | V/mA Analog Input 13 | x.xx | mA | ||||
75 | V/mA Analog Input 14 | x.xx | mA | ||||
76 | V/mA Analog Input 15 | x.xx | mA | ||||
77 | V/mA Analog Input 16 | N/A | N/A | Temperature input. Always 0. | |||
78 | V/mA Analog Input 17 | N/A | N/A | Temperature input. Always 0. | |||
79 | V/mA Analog Input 18 | N/A | N/A | Temperature input. Always 0. | |||
80 | V/mA Analog Input 19 | N/A | N/A | Temperature input. Always 0. | |||
81 | V/mA Analog Input 20 | N/A | N/A | Temperature input. Always 0. | |||
82 | V/mA Analog Input 21 | N/A | N/A | Temperature input. Always 0. | |||
83 | V/mA Analog Input 22 | N/A | N/A | Temperature input. Always 0. | |||
84 | V/mA Analog Input 23 | N/A | N/A | Temperature input. Always 0. | |||
85 | V/mA (AO1) Pressure Control Valve Position | x.xx | mA | ||||
86 | V/mA (AO2) Multipurpose | x.xx | mA | ||||
142 | Status | x | N/A | 0 = Off 1 = Ready 2 = Pre-Run 3 = Run 4 = Post-Run 5 = Alarm 6 = Shutdown 7 = Fault 8 = Restart |
|||
143 | Alarm | x | N/A | See Alarm list for values. | |||
144 | Shutdown | x | N/A | See Shutdown list for values. | |||
145 | Fault | x | N/A | See Fault list for values. | |||
146 | Fault VFD | x | N/A | See Fault VFD list for values. | |||
147 | Shutdown Restart Type | x | N/A | 1 = Manual 2 = Timed |
|||
148 | Shutdown Restart Time | x | Minutes | ||||
149 | Shutdown Restart Countdown | x | Minutes | ||||
150 | Fault Restart Type | x | 1 = Manual 2 = Timed |
||||
151 | Fault Restart Time | x | Minutes | ||||
152 | Fault Restart Countdown | x | Minutes | ||||
153 | Capacity | x.x | HP | ||||
154 | Rated Current | x.x | A | ||||
155 | Reference Frequency | x.xx | Hz | ||||
156 | Output Frequency | x.xx | Hz | ||||
157 | Motor Voltage | x.x | VAC | ||||
158 | Motor Current | x.x | A | ||||
159 | Motor Torque | x | LbFt | ||||
160 | DC Bus | x | VDC | ||||
161 | Motor Speed | x | RPM | ||||
164 | Pre-Run State | x | 0 = Waiting 1 = Thrust Chamber Oil Pump Run 2 = Block Valve Open 3 = Pressure Control Valve Position 4 = Charge Pump Run 5 = Done |
||||
165 | Post-Run State FUTURE USE | x | |||||
166 | Motor Horsepower | x.x | HP | ||||
167 | Motor Synchronous Speed | x | RPM | ||||
168 | Motor Poles | x | N/A | ||||
200 | Motor Rated Torque | x | LbFt | ||||
201 | Fault Reference Frequency | x.xx | Hz | ||||
202 | Fault Output Frequency | x.xx | Hz | ||||
203 | Fault Output Voltage | x.x | VAC | ||||
204 | Fault Output Current | x.x | A | ||||
205 | Fault Output Torque | x | LbFt | ||||
206 | Fault DC Bus | x | VDC | ||||
207 | Fault Motor Horsepower | x.x | HP | ||||
208 | Fault Motor Speed | x | RPM | ||||
209 | Fault Internal Temp | x | DegC | ||||
210 | Fault Heatsink Temp | x | DegC | ||||
211 | Fault Internal Temp | x | DegF | ||||
212 | Fault Heatsink Temp | x | DegF | ||||
213 | Internal Temp | x | DegF | ||||
214 | Heatsink Temp | x | DegF | ||||
215 | Pressure Control Valve Commanded Position | x.x | % | ||||
228 | Auto Pump Curve Discharge Pressure Target | x | PSI | ||||
229 | Discharge Pressure Target | x | PSI | ||||
230 | SD Card Status | x | 0 = No SD Card 1 = Present - Read-Only 2 = Present - OK |
||||
231 | SD Logging Status | x | 0 = Stopped 1 = Active |
||||
232 | Access Level | x | 1 = View-Only 2 = Limited Operator 3 = Full Supervisor 4 = Factory |
||||
233 | Pressure Control Valve Position Error | x.x | % | ||||
242 | Speed Error | x.xx | Hz | ||||
243 | Discharge Pressure Error | x | PSI | ||||
244 | Discharge Error Lower Limit | x | PSI | ||||
245 | Discharge Error Upper Limit | x | PSI | ||||
251 | Thrust Chamber Oil Temperature | x.x | DegF | Works with either AI10 or AI16. | |||
252 | Input Power | x.x | kW | ||||
254 | Curve Area Lower Bounds | x.xx | Hz | ||||
255 | Curve Area Upper Bounds | x.xx | Hz | ||||
256 | Pressure Control Valve Control Mode | x | 0 = Auto Pump Curve 1 = Manual Pressure 2 = Manual Position |
||||
257 | Block Valve Status | x | 0 = Disabled 1 = Command Open 2 = Command Close 3 = Opening 4 = Closing 5 = Open 6 = Closed 7 = Open and Closed |
||||
258 | Block Valve Commanded Position | x.x | % | ||||
259 | Last Version Software/Firmware/Program | x.xx | |||||
260 | Pump Curve Generation State | x | 0 | 4 |
0 = Idle 1 = Initialization 2 = Min/Max 3 = Points 4 = Reset, Go Idle |
||
261 | Pump Curve Generation Progress | x | % | ||||
262 | Pump Curve Generation Steps | x | |||||
263 | Screensaver Picture Index | ||||||
264 | Maintenance Reminder 1 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
265 | Maintenance Reminder 1 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
266 | Maintenance Reminder 1 Time Remaining | x | Hrs | ||||
267 | Maintenance Reminder 1 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
268 | Maintenance Reminder 2 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
269 | Maintenance Reminder 2 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
270 | Maintenance Reminder 2 Time Remaining | x | Hrs | ||||
271 | Maintenance Reminder 2 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
272 | Maintenance Reminder 3 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
273 | Maintenance Reminder 3 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
274 | Maintenance Reminder 3 Time Remaining | x | Hrs | ||||
275 | Maintenance Reminder 3 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
276 | Maintenance Reminder 4 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
277 | Maintenance Reminder 4 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
278 | Maintenance Reminder 4 Time Remaining | x | Hrs | ||||
279 | Maintenance Reminder 4 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
280 | Maintenance Reminder 5 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
281 | Maintenance Reminder 5 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
282 | Maintenance Reminder 5 Time Remaining | x | Hrs | ||||
283 | Maintenance Reminder 5 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
284 | Maintenance Reminder 6 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
285 | Maintenance Reminder 6 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
286 | Maintenance Reminder 6 Time Remaining | x | Hrs | ||||
287 | Maintenance Reminder 6 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
288 | Maintenance Reminder 7 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
289 | Maintenance Reminder 7 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
290 | Maintenance Reminder 7 Time Remaining | x | Hrs | ||||
291 | Maintenance Reminder 7 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
292 | Maintenance Reminder 8 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
293 | Maintenance Reminder 8 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
294 | Maintenance Reminder 8 Time Remaining | x | Hrs | ||||
295 | Maintenance Reminder 8 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
296 | Maintenance Reminder 9 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
297 | Maintenance Reminder 9 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
298 | Maintenance Reminder 9 Time Remaining | x | Hrs | ||||
299 | Maintenance Reminder 9 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
300 | Maintenance Reminder 10 Frequency | x | 0 | 2 |
0 = Disabled 1 = Run-Time 2 = Monthly |
||
301 | Maintenance Reminder 10 Run-Time Source | x | 0 | 3 |
0 = Panel 1 = Main Pump 2 = Charge Pump 3 = Thrust Chamber Oil Pump |
||
302 | Maintenance Reminder 10 Time Remaining | x | Hrs | ||||
303 | Maintenance Reminder 10 Status | x | 0 | 2 |
0 = Disabled 1 = OK 2 = Attention |
||
304 | RESERVED | ||||||
305 | Tank Screen Tank 1 Level | x.x | |||||
306 | Tank Screen Tank 1 Scale Minimum | x.x | |||||
307 | Tank Screen Tank 1 Scale Maximum | x.x | |||||
308 | Tank Screen Tank 2 Level | x.x | |||||
309 | Tank Screen Tank 2 Scale Minimum | x.x | |||||
310 | Tank Screen Tank 2 Scale Maximum | x.x | |||||
311 | Tank Screen Tank 3 Level | x.x | |||||
312 | Tank Screen Tank 3 Scale Minimum | x.x | |||||
313 | Tank Screen Tank 3 Scale Maximum | x.x | |||||
314 | Tank Screen Tank 4 Level | x.x | |||||
315 | Tank Screen Tank 4 Scale Minimum | x.x | |||||
316 | Tank Screen Tank 4 Scale Maximum | x.x | |||||
317 | Tank Screen Tank 5 Level | x.x | |||||
318 | Tank Screen Tank 5 Scale Minimum | x.x | |||||
319 | Tank Screen Tank 5 Scale Maximum | x.x | |||||
320 | Tank Screen Tank 6 Level | x.x | |||||
321 | Tank Screen Tank 6 Scale Minimum | x.x | |||||
322 | Tank Screen Tank 6 Scale Maximum | x.x | |||||
323 | VFD Heatsink Rated Overtemperature Threshold | x | DegC | ||||
324 | VFD Thermal Warning Threshold | x | DegC |
Monitors (32-Bit Holding Registers) – Read-Only (0x03)
Address | Description | Scaling | Units | Minimum | Maximum | Values | Notes |
28672 | Scaled Analog Input 7 | x | BPD | ||||
28673 | Scaled Analog Input 8 | x | |||||
28692 | Accumulated/Totalized Analog Input 7 Today | x | Brrls | ||||
28693 | Accumulated/Totalized Analog Input 7 Previous Day | x | Brrls | ||||
28694 | Accumulated/Totalized Analog Input 8 Today | x | Brrls | ||||
28695 | Accumulated/Totalized Analog Input 8 Previous Day | x | Brrls | ||||
28694 | Main Pump Run Time | x | Secs | ||||
28695 | Thrust Chamber Oil Pump Run Time | x | Secs | ||||
28696 | Charge Pump Run Time | x | Secs | ||||
28697 | Main Pump Run Time | x.x | Hrs | ||||
28698 | Thrust Chamber Oil Pump Run Time | x.x | Hrs | ||||
28699 | Charge Pump Run Time | x.x | Hrs | ||||
28700 | Power-Loss RTC Date | x | MMDDYY | ||||
28701 | Power-Loss RTC Time | x | HHMMSS | ||||
28702 | Panel Run Time | x | Secs | ||||
28703 | Panel Run Time | x.x | Hrs | ||||
28704 | Maintenance Reminder 1 Time Remaining | x | Secs | ||||
28705 | Maintenance Reminder 2 Time Remaining | x | Secs | ||||
28706 | Maintenance Reminder 3 Time Remaining | x | Secs | ||||
28707 | Maintenance Reminder 4 Time Remaining | x | Secs | ||||
28708 | Maintenance Reminder 5 Time Remaining | x | Secs | ||||
28709 | Maintenance Reminder 6 Time Remaining | x | Secs | ||||
28710 | Maintenance Reminder 7 Time Remaining | x | Secs | ||||
28711 | Maintenance Reminder 8 Time Remaining | x | Secs | ||||
28712 | Maintenance Reminder 9 Time Remaining | x | Secs | ||||
28713 | Maintenance Reminder 10 Time Remaining | x | Secs |
Monitors (Bits/Coils) – Read-Only (0x01)
Address | Description | Notes |
10 | Command Hand | |
11 | Command Auto | |
12 | Command Run | |
13 | Command Forward | |
14 | Command Reverse | |
15 | Command Reset Shutdown/Fault | |
16 | Command Motor Auto-Tune | |
17 | Command Reset SD Log | |
18 | Command Reset Manual | |
19 | Command PID1 Pressure Control Valve Auto-Tune | |
20 | Command PID2 Speed Auto-Tune | |
21 | Command 7-Point Auto Bounds | |
22 | Command Clear Events | |
23 | Command Reset kWh | |
24 | Command Reset SCADA | |
25 | Command Bit 15 | |
28 | Status 1 Forward | |
29 | Status 1 Reverse | |
30 | Status 1 Pre-Run | |
31 | Status 1 Run | |
32 | Status 1 Post Run | |
33 | Status 1 Alarm | |
34 | Status 1 Shutdown | |
35 | Status 1 Fault | |
36 | Status 1 Fault VFD | |
37 | Status 1 Restart | |
38 | Status 1 Current Limiting | |
39 | Status 1 Torque Limiting | |
40 | Status 1 Accelerating | |
41 | Status 1 Decelerating | |
42 | Status 1 OptiMode | |
43 | Status 1 Maintenance Required | |
46 | Status 2 Master Enable | |
47 | Status 2 Bit 1 | |
48 | Status 2 Bit 2 | |
49 | Status 2 Bit 3 | |
50 | Status 2 Bit 4 | |
51 | Status 2 Bit 5 | |
52 | Status 2 Bit 6 | |
53 | Status 2 Bit 7 | |
54 | Status 2 Bit 8 | |
55 | Status 2 Bit 10 | |
56 | Status 2 Bit 11 | |
57 | Status 2 Bit 12 | |
58 | Status 2 Bit 13 | |
59 | Status 2 Bit 14 | |
60 | Status 2 Bit 15 | |
61 | Status 2 Bit 16 | |
100 | Active Digital Input 1 | |
101 | Active Digital Input 2 | |
102 | Active Digital Input 3 | |
103 | Active Digital Input 4 | |
104 | Active Digital Input 5 | |
105 | Active Digital Input 6 | |
106 | Active Digital Input 7 | |
107 | Active Digital Input 8 | |
108 | Active Digital Input 9 | |
109 | Active Digital Input 10 | |
110 | Active Digital Input 11 | |
111 | Active Digital Input 12 | |
112 | Active Digital Input 13 | |
113 | Active Digital Input 14 | |
114 | Active Digital Input 15 | |
115 | Active Digital Input 16 | |
116 | Active (DO01) Charge Pump Run | |
117 | Active (DO02) Thrust Chamber Oil Pump Run | |
118 | Active (DO03) Block Valve Open | |
119 | Active (DO04) Heat Trace On | |
120 | Active (DO05) Hand Active | |
121 | Active (DO06) Run | |
122 | Active (DO07) Alarm | |
123 | Active (DO08) Shutdown | |
124 | Active (DO09) Fault | |
125 | Active (DO10) Status Ready (Yellow) | |
126 | Active (DO11) Status Run (Green) | |
127 | Active (DO12) Status Problem (Red) | |
128 | Active (DO13) Spare 1 | |
129 | Active (DO14) Spare 2 | |
130 | Active (DO15) Spare 3 | |
131 | Active (DO16) Spare 4 | |
200 | Alarm Active None | |
201 | Alarm Active Multiple | |
202 | Alarm Active Analog Input 1 High-High | |
203 | Alarm Active Analog Input 1 High | |
204 | Alarm Active Analog Input 1 Low | |
205 | Alarm Active Analog Input 1 Low-Low | |
206 | Alarm Active Analog Input 2 High-High | |
207 | Alarm Active Analog Input 2 High | |
208 | Alarm Active Analog Input 2 Low | |
209 | Alarm Active Analog Input 2 Low-Low | |
210 | Alarm Active Analog Input 3 High-High | |
211 | Alarm Active Analog Input 3 High | |
212 | Alarm Active Analog Input 3 Low | |
213 | Alarm Active Analog Input 3 Low-Low | |
214 | Alarm Active Analog Input 4 High-High | |
215 | Alarm Active Analog Input 4 High | |
216 | Alarm Active Analog Input 4 Low | |
217 | Alarm Active Analog Input 4 Low-Low | |
218 | Alarm Active Analog Input 5 High-High | |
219 | Alarm Active Analog Input 5 High | |
220 | Alarm Active Analog Input 5 Low | |
221 | Alarm Active Analog Input 5 Low-Low | |
222 | Alarm Active Analog Input 6 High-High | |
223 | Alarm Active Analog Input 6 High | |
224 | Alarm Active Analog Input 6 Low | |
225 | Alarm Active Analog Input 6 Low-Low | |
226 | Alarm Active Analog Input 7 High-High | |
227 | Alarm Active Analog Input 7 High | |
228 | Alarm Active Analog Input 7 Low | |
229 | Alarm Active Analog Input 7 Low-Low | |
230 | Alarm Active Analog Input 8 High-High | |
231 | Alarm Active Analog Input 8 High | |
232 | Alarm Active Analog Input 8 Low | |
233 | Alarm Active Analog Input 8 Low-Low | |
234 | Alarm Active Analog Input 9 High-High | |
235 | Alarm Active Analog Input 9 High | |
236 | Alarm Active Analog Input 9 Low | |
237 | Alarm Active Analog Input 9 Low-Low | |
238 | Alarm Active Analog Input 10 High-High | |
239 | Alarm Active Analog Input 10 High | |
240 | Alarm Active Analog Input 10 Low | |
241 | Alarm Active Analog Input 10 Low-Low | |
242 | Alarm Active Analog Input 11 High-High | |
243 | Alarm Active Analog Input 11 High | |
244 | Alarm Active Analog Input 11 Low | |
245 | Alarm Active Analog Input 11 Low-Low | |
246 | Alarm Active Analog Input 12 High-High | |
247 | Alarm Active Analog Input 12 High | |
248 | Alarm Active Analog Input 12 Low | |
249 | Alarm Active Analog Input 12 Low-Low | |
250 | Alarm Active Analog Input 13 High-High | |
251 | Alarm Active Analog Input 13 High | |
252 | Alarm Active Analog Input 13 Low | |
253 | Alarm Active Analog Input 13 Low-Low | |
254 | Alarm Active Analog Input 14 High-High | |
255 | Alarm Active Analog Input 14 High | |
256 | Alarm Active Analog Input 14 Low | |
257 | Alarm Active Analog Input 14 Low-Low | |
258 | Alarm Active Analog Input 15 High-High | |
259 | Alarm Active Analog Input 15 High | |
260 | Alarm Active Analog Input 15 Low | |
261 | Alarm Active Analog Input 15 Low-Low | |
262 | Alarm Active Analog Input 16 High-High | |
263 | Alarm Active Analog Input 16 High | |
264 | Alarm Active Analog Input 16 Low | |
265 | Alarm Active Analog Input 16 Low-Low | |
266 | Alarm Active Analog Input 17 High-High | |
267 | Alarm Active Analog Input 17 High | |
268 | Alarm Active Analog Input 17 Low | |
269 | Alarm Active Analog Input 17 Low-Low | |
270 | Alarm Active Analog Input 18 High-High | |
271 | Alarm Active Analog Input 18 High | |
272 | Alarm Active Analog Input 18 Low | |
273 | Alarm Active Analog Input 18 Low-Low | |
274 | Alarm Active Analog Input 19 High-High | |
275 | Alarm Active Analog Input 19 High | |
276 | Alarm Active Analog Input 19 Low | |
277 | Alarm Active Analog Input 19 Low-Low | |
278 | Alarm Active Analog Input 20 High-High | |
279 | Alarm Active Analog Input 20 High | |
280 | Alarm Active Analog Input 20 Low | |
281 | Alarm Active Analog Input 20 Low-Low | |
282 | Alarm Active Analog Input 21 High-High | |
283 | Alarm Active Analog Input 21 High | |
284 | Alarm Active Analog Input 21 Low | |
285 | Alarm Active Analog Input 21 Low-Low | |
286 | Alarm Active Analog Input 22 High-High | |
287 | Alarm Active Analog Input 22 High | |
288 | Alarm Active Analog Input 22 Low | |
289 | Alarm Active Analog Input 22 Low-Low | |
290 | Alarm Active Analog Input 23 High-High | |
291 | Alarm Active Analog Input 23 High | |
292 | Alarm Active Analog Input 23 Low | |
293 | Alarm Active Analog Input 23 Low-Low | |
294 | Alarm Active Filter Differential Pressure High-High | |
295 | Alarm Active Filter Differential Pressure High | |
296 | Alarm Active Digital Input 1 | |
297 | Alarm Active Digital Input 2 | |
298 | Alarm Active Digital Input 3 | |
299 | Alarm Active Digital Input 4 | |
300 | Alarm Active Digital Input 5 | |
301 | Alarm Active Digital Input 6 | |
302 | Alarm Active Digital Input 7 | |
303 | Alarm Active Digital Input 8 | |
304 | Alarm Active Digital Input 9 | |
305 | Alarm Active Digital Input 10 | |
306 | Alarm Active Digital Input 11 | |
307 | Alarm Active Digital Input 12 | |
308 | Alarm Active Digital Input 13 | |
309 | Alarm Active Digital Input 14 | |
310 | Alarm Active Digital Input 15 | |
311 | Alarm Active Digital Input 16 | |
312 | Alarm Active Main Pump Speed Mismatch | |
313 | Alarm Active Main Pump Out of Curve | |
314 | Alarm Active Pressure Control Valve Failed to Control Pressure | |
315 | Alarm Active Block Valve Open | |
316 | Alarm Active Block Valve Closed | |
317 | Alarm Active VFD Heatsink Thermal Warning | |
400 | Alarm Active Analog Input 1 Any | Set when ANY alarm is active for Analog Input 1 (High-High, High, Low, Low-Low). |
401 | Alarm Active Analog Input 2 Any | Set when ANY alarm is active for Analog Input 2 (High-High, High, Low, Low-Low). |
402 | Alarm Active Analog Input 3 Any | Set when ANY alarm is active for Analog Input 3 (High-High, High, Low, Low-Low). |
403 | Alarm Active Analog Input 4 Any | Set when ANY alarm is active for Analog Input 4 (High-High, High, Low, Low-Low). |
404 | Alarm Active Analog Input 5 Any | Set when ANY alarm is active for Analog Input 5 (High-High, High, Low, Low-Low). |
405 | Alarm Active Analog Input 6 Any | Set when ANY alarm is active for Analog Input 6 (High-High, High, Low, Low-Low). |
406 | Alarm Active Analog Input 7 Any | Set when ANY alarm is active for Analog Input 7 (High-High, High, Low, Low-Low). |
407 | Alarm Active Analog Input 8 Any | Set when ANY alarm is active for Analog Input 8 (High-High, High, Low, Low-Low). |
408 | Alarm Active Analog Input 9 Any | Set when ANY alarm is active for Analog Input 9 (High-High, High, Low, Low-Low). |
409 | Alarm Active Analog Input 10 Any | Set when ANY alarm is active for Analog Input 10 (High-High, High, Low, Low-Low). |
410 | Alarm Active Analog Input 11 Any | Set when ANY alarm is active for Analog Input 11 (High-High, High, Low, Low-Low). |
411 | Alarm Active Analog Input 12 Any | Set when ANY alarm is active for Analog Input 12 (High-High, High, Low, Low-Low). |
412 | Alarm Active Analog Input 13 Any | Set when ANY alarm is active for Analog Input 13 (High-High, High, Low, Low-Low). |
413 | Alarm Active Analog Input 14 Any | Set when ANY alarm is active for Analog Input 14 (High-High, High, Low, Low-Low). |
414 | Alarm Active Analog Input 15 Any | Set when ANY alarm is active for Analog Input 15 (High-High, High, Low, Low-Low). |
415 | Alarm Active Analog Input 16 Any | Set when ANY alarm is active for Analog Input 16 (High-High, High, Low, Low-Low). |
416 | Alarm Active Analog Input 17 Any | Set when ANY alarm is active for Analog Input 17 (High-High, High, Low, Low-Low). |
417 | Alarm Active Analog Input 18 Any | Set when ANY alarm is active for Analog Input 18 (High-High, High, Low, Low-Low). |
418 | Alarm Active Analog Input 19 Any | Set when ANY alarm is active for Analog Input 19 (High-High, High, Low, Low-Low). |
419 | Alarm Active Analog Input 20 Any | Set when ANY alarm is active for Analog Input 20 (High-High, High, Low, Low-Low). |
420 | Alarm Active Analog Input 21 Any | Set when ANY alarm is active for Analog Input 21 (High-High, High, Low, Low-Low). |
421 | Alarm Active Analog Input 22 Any | Set when ANY alarm is active for Analog Input 22 (High-High, High, Low, Low-Low). |
422 | Alarm Active Analog Input 23 Any | Set when ANY alarm is active for Analog Input 23 (High-High, High, Low, Low-Low). |
423 | Alarm Active Filter Differential Pressure Any | Set when ANY alarm is active for Filter Differential Pressure (High-High, High). |
440 | Maintenance Reminder Maintenance Required Any | Set when ANY maintenance reminder is active. |
441 | Maintenance Reminder 1 Maintenance Required | |
442 | Maintenance Reminder 2 Maintenance Required | |
443 | Maintenance Reminder 3 Maintenance Required | |
444 | Maintenance Reminder 4 Maintenance Required | |
445 | Maintenance Reminder 5 Maintenance Required | |
446 | Maintenance Reminder 6 Maintenance Required | |
447 | Maintenance Reminder 7 Maintenance Required | |
448 | Maintenance Reminder 8 Maintenance Required | |
449 | Maintenance Reminder 9 Maintenance Required | |
450 | Maintenance Reminder 10 Maintenance Required |
Alarm Codes (Register 143)
Code | Description | Notes |
0 | None | |
1 | Multiple | |
2 | Analog Input 1 High-High | |
3 | Analog Input 1 High | |
4 | Analog Input 1 Low | |
5 | Analog Input 1 Low-Low | |
6 | Analog Input 2 High-High | |
7 | Analog Input 2 High | |
8 | Analog Input 2 Low | |
9 | Analog Input 2 Low-Low | |
10 | Analog Input 3 High-High | |
11 | Analog Input 3 High | |
12 | Analog Input 3 Low | |
13 | Analog Input 3 Low-Low | |
14 | Analog Input 4 High-High | |
15 | Analog Input 4 High | |
16 | Analog Input 4 Low | |
17 | Analog Input 4 Low-Low | |
18 | Analog Input 5 High-High | |
19 | Analog Input 5 High | |
20 | Analog Input 5 Low | |
21 | Analog Input 5 Low-Low | |
22 | Analog Input 6 High-High | |
23 | Analog Input 6 High | |
24 | Analog Input 6 Low | |
25 | Analog Input 6 Low-Low | |
26 | Analog Input 7 High-High | |
27 | Analog Input 7 High | |
28 | Analog Input 7 Low | |
29 | Analog Input 7 Low-Low | |
30 | Analog Input 8 High-High | |
31 | Analog Input 8 High | |
32 | Analog Input 8 Low | |
33 | Analog Input 8 Low-Low | |
34 | Analog Input 9 High-High | |
35 | Analog Input 9 High | |
36 | Analog Input 9 Low | |
37 | Analog Input 9 Low-Low | |
38 | Analog Input 10 High-High | |
39 | Analog Input 10 High | |
40 | Analog Input 10 Low | |
41 | Analog Input 10 Low-Low | |
42 | Analog Input 11 High-High | |
43 | Analog Input 11 High | |
44 | Analog Input 11 Low | |
45 | Analog Input 11 Low-Low | |
46 | Analog Input 12 High-High | |
47 | Analog Input 12 High | |
48 | Analog Input 12 Low | |
49 | Analog Input 12 Low-Low | |
50 | Analog Input 13 High-High | |
51 | Analog Input 13 High | |
52 | Analog Input 13 Low | |
53 | Analog Input 13 Low-Low | |
54 | Analog Input 14 High-High | |
55 | Analog Input 14 High | |
56 | Analog Input 14 Low | |
57 | Analog Input 14 Low-Low | |
58 | Analog Input 15 High-High | |
59 | Analog Input 15 High | |
60 | Analog Input 15 Low | |
61 | Analog Input 15 Low-Low | |
62 | Analog Input 16 High-High | |
63 | Analog Input 16 High | |
64 | Analog Input 16 Low | |
65 | Analog Input 16 Low-Low | |
66 | Analog Input 17 High-High | |
67 | Analog Input 17 High | |
68 | Analog Input 17 Low | |
69 | Analog Input 17 Low-Low | |
70 | Analog Input 18 High-High | |
71 | Analog Input 18 High | |
72 | Analog Input 18 Low | |
73 | Analog Input 18 Low-Low | |
74 | Analog Input 19 High-High | |
75 | Analog Input 19 High | |
76 | Analog Input 19 Low | |
77 | Analog Input 19 Low-Low | |
78 | Analog Input 20 High-High | |
79 | Analog Input 20 High | |
80 | Analog Input 20 Low | |
81 | Analog Input 20 Low-Low | |
82 | Analog Input 21 High-High | |
83 | Analog Input 21 High | |
84 | Analog Input 21 Low | |
85 | Analog Input 21 Low-Low | |
86 | Analog Input 22 High-High | |
87 | Analog Input 22 High | |
88 | Analog Input 22 Low | |
89 | Analog Input 22 Low-Low | |
90 | Analog Input 23 High-High | |
91 | Analog Input 23 High | |
92 | Analog Input 23 Low | |
93 | Analog Input 23 Low-Low | |
94 | Filter Differential Pressure High-High | |
95 | Filter Differential Pressure High | |
96 | Digital Input 1 | |
97 | Digital Input 2 | |
98 | Digital Input 3 | |
99 | Digital Input 4 | |
100 | Digital Input 5 | |
101 | Digital Input 6 | |
102 | Digital Input 7 | |
103 | Digital Input 8 | |
104 | Digital Input 9 | |
105 | Digital Input 10 | |
106 | Digital Input 11 | |
107 | Digital Input 12 | |
108 | Digital Input 13 | |
109 | Digital Input 14 | |
110 | Digital Input 15 | |
111 | Digital Input 16 | |
112 | Main Pump Speed Mismatch | |
113 | Main Pump Out of Curve | |
114 | Pressure Control Valve Failed to Control Pressure | |
115 | Block Valve Open | |
116 | Block Valve Closed | |
117 | VFD Heatsink Thermal Warning |
Shutdown Codes (Register 144)
Code | Description | Notes |
0 | None | |
1 | RESERVED | |
2 | Analog Input 1 High-High | |
3 | Analog Input 1 High | |
4 | Analog Input 1 Low | |
5 | Analog Input 1 Low-Low | |
6 | Analog Input 2 High-High | |
7 | Analog Input 2 High | |
8 | Analog Input 2 Low | |
9 | Analog Input 2 Low-Low | |
10 | Analog Input 3 High-High | |
11 | Analog Input 3 High | |
12 | Analog Input 3 Low | |
13 | Analog Input 3 Low-Low | |
14 | Analog Input 4 High-High | |
15 | Analog Input 4 High | |
16 | Analog Input 4 Low | |
17 | Analog Input 4 Low-Low | |
18 | Analog Input 5 High-High | |
19 | Analog Input 5 High | |
20 | Analog Input 5 Low | |
21 | Analog Input 5 Low-Low | |
22 | Analog Input 6 High-High | |
23 | Analog Input 6 High | |
24 | Analog Input 6 Low | |
25 | Analog Input 6 Low-Low | |
26 | Analog Input 7 High-High | |
27 | Analog Input 7 High | |
28 | Analog Input 7 Low | |
29 | Analog Input 7 Low-Low | |
30 | Analog Input 8 High-High | |
31 | Analog Input 8 High | |
32 | Analog Input 8 Low | |
33 | Analog Input 8 Low-Low | |
34 | Analog Input 9 High-High | |
35 | Analog Input 9 High | |
36 | Analog Input 9 Low | |
37 | Analog Input 9 Low-Low | |
38 | Analog Input 10 High-High | |
39 | Analog Input 10 High | |
40 | Analog Input 10 Low | |
41 | Analog Input 10 Low-Low | |
42 | Analog Input 11 High-High | |
43 | Analog Input 11 High | |
44 | Analog Input 11 Low | |
45 | Analog Input 11 Low-Low | |
46 | Analog Input 12 High-High | |
47 | Analog Input 12 High | |
48 | Analog Input 12 Low | |
49 | Analog Input 12 Low-Low | |
50 | Analog Input 13 High-High | |
51 | Analog Input 13 High | |
52 | Analog Input 13 Low | |
53 | Analog Input 13 Low-Low | |
54 | Analog Input 14 High-High | |
55 | Analog Input 14 High | |
56 | Analog Input 14 Low | |
57 | Analog Input 14 Low-Low | |
58 | Analog Input 15 High-High | |
59 | Analog Input 15 High | |
60 | Analog Input 15 Low | |
61 | Analog Input 15 Low-Low | |
62 | Analog Input 16 High-High | |
63 | Analog Input 16 High | |
64 | Analog Input 16 Low | |
65 | Analog Input 16 Low-Low | |
66 | Analog Input 17 High-High | |
67 | Analog Input 17 High | |
68 | Analog Input 17 Low | |
69 | Analog Input 17 Low-Low | |
70 | Analog Input 18 High-High | |
71 | Analog Input 18 High | |
72 | Analog Input 18 Low | |
73 | Analog Input 18 Low-Low | |
74 | Analog Input 19 High-High | |
75 | Analog Input 19 High | |
76 | Analog Input 19 Low | |
77 | Analog Input 19 Low-Low | |
78 | Analog Input 20 High-High | |
79 | Analog Input 20 High | |
80 | Analog Input 20 Low | |
81 | Analog Input 20 Low-Low | |
82 | Analog Input 21 High-High | |
83 | Analog Input 21 High | |
84 | Analog Input 21 Low | |
85 | Analog Input 21 Low-Low | |
86 | Analog Input 22 High-High | |
87 | Analog Input 22 High | |
88 | Analog Input 22 Low | |
89 | Analog Input 22 Low-Low | |
90 | Analog Input 23 High-High | |
91 | Analog Input 23 High | |
92 | Analog Input 23 Low | |
93 | Analog Input 23 Low-Low | |
94 | Filter Differential Pressure High-High | |
95 | Filter Differential Pressure High | |
96 | Digital Input 1 | |
97 | Digital Input 2 | |
98 | Digital Input 3 | |
99 | Digital Input 4 | |
100 | Digital Input 5 | |
101 | Digital Input 6 | |
102 | Digital Input 7 | |
103 | Digital Input 8 | |
104 | Digital Input 9 | |
105 | Digital Input 10 | |
106 | Digital Input 11 | |
107 | Digital Input 12 | |
108 | Digital Input 13 | |
109 | Digital Input 14 | |
110 | Digital Input 15 | |
111 | Digital Input 16 | |
112 | Main Pump Speed Mismatch | |
113 | Main Pump Out of Curve | |
114 | Pressure Control Valve Failed to Control Pressure |
Fault Codes (Register 145)
Code | Description | Notes |
0 | None | |
1 | VFD Fault | |
2 | Analog Input 1 Signal-Loss | |
3 | Analog Input 2 Signal-Loss | |
4 | Analog Input 3 Signal-Loss | |
5 | Analog Input 4 Signal-Loss | |
6 | Analog Input 5 Signal-Loss | |
7 | Analog Input 6 Signal-Loss | |
8 | Analog Input 7 Signal-Loss | |
9 | Analog Input 8 Signal-Loss | |
10 | Analog Input 9 Signal-Loss | |
11 | Analog Input 10 Signal-Loss | |
12 | Analog Input 11 Signal-Loss | |
13 | Analog Input 12 Signal-Loss | |
14 | Analog Input 13 Signal-Loss | |
15 | Analog Input 14 Signal-Loss | |
16 | Analog Input 15 Signal-Loss | |
17 | Analog Input 16 Signal-Loss | |
18 | Analog Input 17 Signal-Loss | |
19 | Analog Input 18 Signal-Loss | |
20 | Analog Input 19 Signal-Loss | |
21 | Analog Input 20 Signal-Loss | |
22 | Analog Input 21 Signal-Loss | |
23 | Analog Input 22 Signal-Loss | |
24 | Analog Input 23 Signal-Loss | |
25 | Block Valve Failed to Open | |
26 | Pressure Control Valve Failed to Position | |
27 | Thrust Chamber Oil Pump Failed to Run | |
28 | Charge Pump Failed to Run | |
29 | Main Pump Failed to Run | |
30 | VFD Communications Failed | |
31 | VFD Failed to Stop at Start-up | |
32 | Battery Failure | |
33 | Hand and Auto Both Active | |
34 | Block Valve Failed to Close | |
35 | Block Valve Open and Close Both Active |
VFD Fault Codes (Register 146)
Code | Description | Notes |
0 | None | |
1 | (OC1) Overcurrent During Accel | |
2 | (OC2) Overcurrent During Decel | |
3 | (OC3) Overcurrent At Set Speed | |
4 | Undefined VFD Fault 4 | |
5 | EF Ground Fault | |
6 | (OU1) Overvoltage During Accel | |
7 | (OU2) Overvoltage During Decel | |
8 | (OU3) Overvoltage At Set Speed | |
9 | Undefined VFD Fault 9 | |
10 | (LU) Undervoltage | |
11 | (Lin) Input Phase Loss | |
12 | Undefined VFD Fault 12 | |
13 | Undefined VFD Fault 13 | |
14 | (FUS) DC Bus Fuse Blown | |
15 | Undefined VFD Fault 15 | |
16 | (PbF) Charging Circuit Fault | |
17 | (OH1) Heatsink Overheat | |
18 | (OH2) External Shutdown | |
19 | (OH3) Internal Overheat | |
20 | (OH4) Motor PTC/NTC Overheat | |
21 | Undefined VFD Fault 21 | |
22 | (dbH) Braking Resistor Overheat | |
23 | (OL1) Motor Overload | |
24 | (OL2) Motor 2 Overload | |
25 | (OLU) VFD Overload | |
26 | Undefined VFD Fault 26 | |
27 | (OS) Overspeed Protection | |
28 | (PG) PG Disconnected | |
29 | (nrb) NTC Disconnected | |
30 | Undefined VFD Fault 30 | |
31 | (Er1) Memory Error | |
32 | (Er2) Keypad Comm Error | |
33 | (Er3) CPU Error | |
34 | (Er4) Option Card Comm Error | |
35 | (Er5) Option Card Error | |
36 | (Er6) Stop Key Error | |
37 | (Er7) Auto-Tuning Error | |
38 | (Er8) RS485 Comm Port 1 Error | |
39 | Undefined VFD Fault 39 | |
40 | Undefined VFD Fault 40 | |
41 | Undefined VFD Fault 41 | |
42 | Undefined VFD Fault 42 | |
43 | Undefined VFD Fault 43 | |
44 | (OL3) Motor 3 Overload | |
45 | (OL4) Motor 4 Overload | |
46 | (OPL) Output Phase Loss | |
47 | (ErE) Excessive Speed Deviation | |
48 | Undefined VFD Fault 48 | |
49 | Undefined VFD Fault 49 | |
50 | Undefined VFD Fault 50 | |
51 | (ErF) Data Save Error | |
52 | Undefined VFD Fault 52 | |
53 | (ErP) RS485 Comm Port 2 Error | |
54 | (ErH) Hardware Error | |
55 | Undefined VFD Fault 55 | |
56 | Undefined VFD Fault 56 | |
57 | (ECN) Enabled EN1/EN2 Lost | |
58 | (CoF) PID Fdbck Disconnected | |
59 | (dbA) Dynamic Braking Transistor | |
60 | Undefined VFD Fault 60 | |
61 | Undefined VFD Fault 61 | |
62 | Undefined VFD Fault 62 | |
63 | Undefined VFD Fault 63 | |
64 | Undefined VFD Fault 64 | |
65 | Undefined VFD Fault 65 | |
66 | Undefined VFD Fault 66 | |
67 | Undefined VFD Fault 67 | |
68 | Undefined VFD Fault 68 | |
69 | Undefined VFD Fault 69 | |
70 | Undefined VFD Fault 70 | |
71 | Undefined VFD Fault 71 | |
72 | Undefined VFD Fault 72 | |
73 | Undefined VFD Fault 73 | |
74 | Undefined VFD Fault 74 | |
75 | Undefined VFD Fault 75 | |
76 | Undefined VFD Fault 76 | |
77 | Undefined VFD Fault 77 | |
78 | Undefined VFD Fault 78 | |
79 | Undefined VFD Fault 79 | |
80 | Undefined VFD Fault 80 | |
81 | Undefined VFD Fault 81 | |
82 | Undefined VFD Fault 82 | |
83 | Undefined VFD Fault 83 | |
84 | Undefined VFD Fault 84 | |
85 | Undefined VFD Fault 85 | |
86 | Undefined VFD Fault 86 | |
87 | Undefined VFD Fault 87 | |
88 | Undefined VFD Fault 88 | |
89 | Undefined VFD Fault 89 | |
90 | Undefined VFD Fault 90 | |
91 | Undefined VFD Fault 91 | |
92 | Undefined VFD Fault 92 | |
93 | Undefined VFD Fault 93 | |
94 | Undefined VFD Fault 94 | |
95 | Undefined VFD Fault 95 | |
96 | Undefined VFD Fault 96 | |
97 | Undefined VFD Fault 97 | |
98 | Undefined VFD Fault 98 | |
99 | Undefined VFD Fault 99 | |
100 | (FAL) Internal DC Fan Failure | |
101 | (OL) Motor Overload Warn | |
102 | (OH) Cooling Fin Overheat Warn | |
103 | (LiF) Component Life Warn | |
104 | (rEF) Command Loss | |
105 | (Pid) PID Output Warn | |
106 | (UTL) Low Torque Detected | |
107 | (PTC) Thermistor Loss | |
108 | (rTE) Machine Life Accum Hours | |
109 | (CnT) Machine Life Start Count | |
110 | Undefined VFD Fault 110 | |
111 | Undefined VFD Fault 111 | |
112 | Undefined VFD Fault 112 | |
113 | Undefined VFD Fault 113 | |
114 | Undefined VFD Fault 114 | |
115 | Undefined VFD Fault 115 | |
116 | Undefined VFD Fault 116 | |
117 | Undefined VFD Fault 117 | |
118 | Undefined VFD Fault 118 | |
119 | Undefined VFD Fault 119 | |
120 | Undefined VFD Fault 120 | |
121 | Undefined VFD Fault 121 | |
122 | Undefined VFD Fault 122 | |
123 | Undefined VFD Fault 123 | |
124 | Undefined VFD Fault 124 | |
125 | Undefined VFD Fault 125 | |
126 | Undefined VFD Fault 126 | |
127 | Undefined VFD Fault 127 | |
128 | Undefined VFD Fault 128 | |
129 | Undefined VFD Fault 129 | |
130 | Undefined VFD Fault 130 | |
131 | Undefined VFD Fault 131 | |
132 | Undefined VFD Fault 132 | |
133 | Undefined VFD Fault 133 | |
134 | Undefined VFD Fault 134 | |
135 | Undefined VFD Fault 135 | |
136 | Undefined VFD Fault 136 | |
137 | Undefined VFD Fault 137 | |
138 | Undefined VFD Fault 138 | |
139 | Undefined VFD Fault 139 | |
140 | Undefined VFD Fault 140 | |
141 | Undefined VFD Fault 141 | |
142 | Undefined VFD Fault 142 | |
143 | Undefined VFD Fault 143 | |
144 | Undefined VFD Fault 144 | |
145 | Undefined VFD Fault 145 | |
146 | Undefined VFD Fault 146 | |
147 | Undefined VFD Fault 147 | |
148 | Undefined VFD Fault 148 | |
149 | Undefined VFD Fault 149 | |
150 | Undefined VFD Fault 150 | |
151 | Undefined VFD Fault 151 | |
152 | Undefined VFD Fault 152 | |
153 | Undefined VFD Fault 153 | |
154 | Undefined VFD Fault 154 | |
155 | Undefined VFD Fault 155 | |
156 | Undefined VFD Fault 156 | |
157 | Undefined VFD Fault 157 | |
158 | Undefined VFD Fault 158 | |
159 | Undefined VFD Fault 159 | |
160 | Undefined VFD Fault 160 | |
161 | Undefined VFD Fault 161 | |
162 | Undefined VFD Fault 162 | |
163 | Undefined VFD Fault 163 | |
164 | Undefined VFD Fault 164 | |
165 | Undefined VFD Fault 165 | |
166 | Undefined VFD Fault 166 | |
167 | Undefined VFD Fault 167 | |
168 | Undefined VFD Fault 168 | |
169 | Undefined VFD Fault 169 | |
170 | Undefined VFD Fault 170 | |
171 | Undefined VFD Fault 171 | |
172 | Undefined VFD Fault 172 | |
173 | Undefined VFD Fault 173 | |
174 | Undefined VFD Fault 174 | |
175 | Undefined VFD Fault 175 | |
176 | Undefined VFD Fault 176 | |
177 | Undefined VFD Fault 177 | |
178 | Undefined VFD Fault 178 | |
179 | Undefined VFD Fault 179 | |
180 | Undefined VFD Fault 180 | |
181 | Undefined VFD Fault 181 | |
182 | Undefined VFD Fault 182 | |
183 | Undefined VFD Fault 183 | |
184 | Undefined VFD Fault 184 | |
185 | Undefined VFD Fault 185 | |
186 | Undefined VFD Fault 186 | |
187 | Undefined VFD Fault 187 | |
188 | Undefined VFD Fault 188 | |
189 | Undefined VFD Fault 189 | |
190 | Undefined VFD Fault 190 | |
191 | Undefined VFD Fault 191 | |
192 | Undefined VFD Fault 192 | |
193 | Undefined VFD Fault 193 | |
194 | Undefined VFD Fault 194 | |
195 | Undefined VFD Fault 195 | |
196 | Undefined VFD Fault 196 | |
197 | Undefined VFD Fault 197 | |
198 | Undefined VFD Fault 198 | |
199 | Undefined VFD Fault 199 | |
200 | Undefined VFD Fault 200 | |
201 | Undefined VFD Fault 201 | |
202 | Undefined VFD Fault 202 | |
203 | Undefined VFD Fault 203 | |
204 | Undefined VFD Fault 204 | |
205 | Undefined VFD Fault 205 | |
206 | Undefined VFD Fault 206 | |
207 | Undefined VFD Fault 207 | |
208 | Undefined VFD Fault 208 | |
209 | Undefined VFD Fault 209 | |
210 | Undefined VFD Fault 210 | |
211 | Undefined VFD Fault 211 | |
212 | Undefined VFD Fault 212 | |
213 | Undefined VFD Fault 213 | |
214 | Undefined VFD Fault 214 | |
215 | Undefined VFD Fault 215 | |
216 | Undefined VFD Fault 216 | |
217 | Undefined VFD Fault 217 | |
218 | Undefined VFD Fault 218 | |
219 | Undefined VFD Fault 219 | |
220 | Undefined VFD Fault 220 | |
221 | Undefined VFD Fault 221 | |
222 | Undefined VFD Fault 222 | |
223 | Undefined VFD Fault 223 | |
224 | Undefined VFD Fault 224 | |
225 | Undefined VFD Fault 225 | |
226 | Undefined VFD Fault 226 | |
227 | Undefined VFD Fault 227 | |
228 | Undefined VFD Fault 228 | |
229 | Undefined VFD Fault 229 | |
230 | Undefined VFD Fault 230 | |
231 | Undefined VFD Fault 231 | |
232 | Undefined VFD Fault 232 | |
233 | Undefined VFD Fault 233 | |
234 | Undefined VFD Fault 234 | |
235 | Undefined VFD Fault 235 | |
236 | Undefined VFD Fault 236 | |
237 | Undefined VFD Fault 237 | |
238 | Undefined VFD Fault 238 | |
239 | Undefined VFD Fault 239 | |
240 | Undefined VFD Fault 240 | |
241 | Undefined VFD Fault 241 | |
242 | Undefined VFD Fault 242 | |
243 | Undefined VFD Fault 243 | |
244 | Undefined VFD Fault 244 | |
245 | Undefined VFD Fault 245 | |
246 | Undefined VFD Fault 246 | |
247 | Undefined VFD Fault 247 | |
248 | Undefined VFD Fault 248 | |
249 | Undefined VFD Fault 249 | |
250 | Undefined VFD Fault 250 | |
251 | Undefined VFD Fault 251 | |
252 | Undefined VFD Fault 252 | |
253 | Undefined VFD Fault 253 | |
254 | (Err) Simulated Fault |
Parameters (16-Bit Holding Registers) – Read/Write
Address | Description | Scaling | Units | Minimum | Maximum | Values | Notes |
3 | SCADA Shutdown/Fault Reset | x | 0 | 1 | 0 = Idle 1 = Reset |
||
4 | RESERVED | ||||||
5 | SCADA Pump Curve Generate Table | x | 0 | 1 |
0 = Idle 1 = Generate Table |
||
500 | Serial Port 1 SCADA Type | x | 1 | 2 |
1 = RS-232 2 = RS-485 |
||
501 | Serial Port 1 SCADA Baud Rate | x | bps | 1 | 5 |
1 = 9600 2 = 19200 3 = 38400 4 = 57800 5 = 115200 |
|
502 | Serial Port 1 SCADA Slave Address | x | 1 | 255 | |||
503 | Serial Port 2 VFD Baud Rate | x | bps | 1 | 3 |
1 = 9600 2 = 19200 3 = 38400 |
|
504 | Serial Port 2 VFD Slave Address | x | 1 | 255 | |||
505 | Screensaver | x | 1 | 3 |
1 = Disabled 3 = Pictures |
||
506 | Screensaver Timeout | x | Minutes | 1 | 60 | ||
507 | Analog Input 1 Scale Minimum | x | -32768 | 32767 | |||
508 | Analog Input 1 Scale Maximum | x | -32768 | 32767 | |||
509 | Analog Input 1 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
510 | Analog Input 1 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
511 | Analog Input 1 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
512 | Analog Input 1 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
513 | Analog Input 1 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
514 | Analog Input 1 High-High Setpoint | x | -32768 | 32767 | |||
515 | Analog Input 1 High Setpoint | x | -32768 | 32767 | |||
516 | Analog Input 1 Low Setpoint | x | -32768 | 32767 | |||
517 | Analog Input 1 Low-Low Setpoint | x | -32768 | 32767 | |||
518 | Analog Input 1 Start Delay | x | Seconds | 1 | 32767 | ||
519 | Analog Input 1 Detection Delay | x | Seconds | 1 | 32767 | ||
520 | Analog Input 1 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
521 | Analog Input 1 Restart Delay | x | Minutes | 1 | 32767 | ||
522 | RESERVED | ||||||
523 | RESERVED | ||||||
524 | Analog Input 2 Scale Minimum | x | PSI | -32768 | 32767 | ||
525 | Analog Input 2 Scale Maximum | x | PSI | -32768 | 32767 | ||
526 | Analog Input 2 Signal-Loss Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
527 | Analog Input 2 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
528 | Analog Input 2 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
529 | Analog Input 2 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
530 | Analog Input 2 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
531 | Analog Input 2 High-High Setpoint | x | PSI | -32768 | 32767 | ||
532 | Analog Input 2 High Setpoint | x | PSI | -32768 | 32767 | ||
533 | Analog Input 2 Low Setpoint | x | PSI | -32768 | 32767 | ||
534 | Analog Input 2 Low-Low Setpoint | x | PSI | -32768 | 32767 | ||
535 | Analog Input 2 Start Delay | x | Seconds | 1 | 32767 | ||
536 | Analog Input 2 Detection Delay | x | Seconds | 1 | 32767 | ||
537 | Analog Input 2 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
538 | Analog Input 2 Restart Delay | x | Minutes | 1 | 32767 | ||
539 | RESERVED | ||||||
540 | RESERVED | ||||||
541 | Analog Input 3 Scale Minimum | x.x | -3276.8 | 3276.7 | |||
542 | Analog Input 3 Maximum | x.x | -3276.8 | 3276.7 | |||
543 | Analog Input 3 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
544 | Analog Input 3 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
545 | Analog Input 3 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
546 | Analog Input 3 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
547 | Analog Input 3 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
548 | Analog Input 3 High-High Setpoint | x.x | -3276.8 | 3276.7 | |||
549 | Analog Input 3 High Setpoint | x.x | -3276.8 | 3276.7 | |||
550 | Analog Input 3 Low Setpoint | x.x | -3276.8 | 3276.7 | |||
551 | Analog Input 3 Low-Low Setpoint | x.x | -3276.8 | 3276.7 | |||
552 | Analog Input 3 Start Delay | x | Seconds | 1 | 32767 | ||
553 | Analog Input 3 Detection Delay | x | Seconds | 1 | 32767 | ||
554 | Analog Input 3 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
555 | Analog Input 3 Restart Delay | x | Minutes | 1 | 32767 | ||
556 | RESERVED | ||||||
557 | RESERVED | ||||||
558 | Analog Input 4 Scale Minimum | x | -32768 | 32767 | |||
559 | Analog Input 4 Scale Maximum | x | -32768 | 32767 | |||
560 | Analog Input 4 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
561 | Analog Input 4 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
562 | Analog Input 4 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
563 | Analog Input 4 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
564 | Analog Input 4 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
565 | Analog Input 4 High-High Setpoint | x | -32768 | 32767 | |||
566 | Analog Input 4 High Setpoint | x | -32768 | 32767 | |||
567 | Analog Input 4 Low Setpoint | x | -32768 | 32767 | |||
568 | Analog Input 4 Low-Low Setpoint | x | -32768 | 32767 | |||
569 | Analog Input 4 Start Delay | x | Seconds | 1 | 32767 | ||
570 | Analog Input 4 Detection Delay | x | Seconds | 1 | 32767 | ||
571 | Analog Input 4 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
572 | Analog Input 4 Restart Delay | x | Minutes | 1 | 32767 | ||
573 | RESERVED | ||||||
574 | RESERVED | ||||||
575 | Analog Input 5 Scale Minimum | x | -32768 | 32767 | |||
576 | Analog Input 5 Scale Maximum | x | -32768 | 32767 | |||
577 | Analog Input 5 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
578 | Analog Input 5 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
579 | Analog Input 5 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
580 | Analog Input 5 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
581 | Analog Input 5 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
582 | Analog Input 5 High-High Setpoint | x | -32768 | 32767 | |||
583 | Analog Input 5 High Setpoint | x | -32768 | 32767 | |||
584 | Analog Input 5 Low Setpoint | x | -32768 | 32767 | |||
585 | Analog Input 5 Low-Low Setpoint | x | -32768 | 32767 | |||
586 | Analog Input 5 Start Delay | x | Seconds | 1 | 32767 | ||
587 | Analog Input 5 Detection Delay | x | Seconds | 1 | 32767 | ||
588 | Analog Input 5 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
589 | Analog Input 5 Restart Delay | x | Minutes | 1 | 32767 | ||
590 | RESERVED | ||||||
591 | RESERVED | ||||||
592 | Analog Input 6 Scale Minimum | x.xx | -327.68 | 327.67 | |||
593 | Analog Input 6 Scale Maximum | x.xx | -327.68 | 327.67 | |||
594 | Analog Input 6 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
595 | Analog Input 6 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
596 | Analog Input 6 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
597 | Analog Input 6 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
598 | Analog Input 6 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
599 | Analog Input 6 High-High Setpoint | x.xx | -327.68 | 327.67 | |||
600 | Analog Input 6 High Setpoint | x.xx | -327.68 | 327.67 | |||
601 | Analog Input 6 Low Setpoint | x.xx | -327.68 | 327.67 | |||
602 | Analog Input 6 Low-Low Setpoint | x.xx | -327.68 | 327.67 | |||
603 | Analog Input 6 Start Delay | x | Seconds | 1 | 32767 | ||
604 | Analog Input 6 Detection Delay | x | Seconds | 1 | 32767 | ||
605 | Analog Input 6 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
606 | Analog Input 6 Restart Delay | x | Minutes | 1 | 32767 | ||
607 | RESERVED | ||||||
608 | RESERVED | ||||||
609 | RESERVED | ||||||
610 | RESERVED | ||||||
611 | Analog Input 7 Flow Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
612 | Analog Input 7 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
613 | Analog Input 7 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
614 | Analog Input 7 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
615 | Analog Input 7 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
616 | RESERVED | ||||||
617 | RESERVED | ||||||
618 | RESERVED | ||||||
619 | RESERVED | ||||||
620 | Analog Input 7 Start Delay | x | Seconds | 1 | 32767 | ||
621 | Analog Input 7 Detection Delay | x | Seconds | 1 | 32767 | ||
622 | Analog Input 7 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
623 | Analog Input 7 Restart Delay | x | Minutes | 1 | 32767 | ||
624 | RESERVED | ||||||
625 | RESERVED | ||||||
626 | RESERVED | ||||||
627 | RESERVED | ||||||
628 | Analog Input 8 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
629 | Analog Input 8 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
630 | Analog Input 8 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
631 | Analog Input 8 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
632 | Analog Input 8 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
633 | RESERVED | ||||||
634 | RESERVED | ||||||
635 | RESERVED | ||||||
636 | RESERVED | ||||||
637 | Analog Input 8 Start Delay | x | Seconds | 1 | 32767 | ||
638 | Analog Input 8 Detection Delay | x | Seconds | 1 | 32767 | ||
639 | Analog Input 8 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
640 | Analog Input 8 Restart Delay | x | Minutes | 1 | 32767 | ||
641 | RESERVED | ||||||
642 | RESERVED | ||||||
643 | Analog Input 9 Scale Minimum | x.x | % | -3276.8 | 3276.7 | ||
644 | Analog Input 9 Scale Maximum | x.x | % | -3276.8 | 3276.7 | ||
645 | Analog Input 9 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
646 | Analog Input 9 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
647 | Analog Input 9 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
648 | Analog Input 9 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
649 | Analog Input 9 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
650 | Analog Input 9 High-High Setpoint | x.x | % | -3276.8 | 3276.7 | ||
651 | Analog Input 9 High Setpoint | x.x | % | -3276.8 | 3276.7 | ||
652 | Analog Input 9 Low Setpoint | x.x | % | -3276.8 | 3276.7 | ||
653 | Analog Input 9 Low-Low Setpoint | x.x | % | -3276.8 | 3276.7 | ||
654 | Analog Input 9 Start Delay | x | Seconds | 1 | 32767 | ||
655 | Analog Input 9 Detection Delay | x | Seconds | 1 | 32767 | ||
656 | Analog Input 9 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
657 | Analog Input 9 Restart Delay | x | Minutes | 1 | 32767 | ||
658 | RESERVED | ||||||
659 | RESERVED | ||||||
660 | RESERVED | ||||||
661 | RESERVED | ||||||
662 | Analog Input 10/16 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
663 | Analog Input 10/16 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
664 | Analog Input 10/16 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
665 | Analog Input 10/16 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
666 | Analog Input 10/16 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
667 | Analog Input 10/16 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
668 | Analog Input 10/16 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
669 | Analog Input 10/16 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
670 | Analog Input 10/16 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
671 | Analog Input 10/16 Start Delay | x | Seconds | 1 | 32767 | ||
672 | Analog Input 10/16 Detection Delay | x | Seconds | 1 | 32767 | ||
673 | Analog Input 10/16 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
674 | Analog Input 10/16 Restart Delay | x | Minutes | 1 | 32767 | ||
675 | RESERVED | ||||||
676 | RESERVED | ||||||
677 | Analog Input 11 Scale Minimum | x.xx | -327.68 | 327.67 | |||
678 | Analog Input 11 Scale Maximum | x.xx | -327.68 | 327.67 | |||
679 | Analog Input 11 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
680 | Analog Input 11 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
681 | Analog Input 11 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
682 | Analog Input 11 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
683 | Analog Input 11 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
684 | Analog Input 11 High-High Setpoint | x.xx | -327.68 | 327.67 | |||
685 | Analog Input 11 High Setpoint | x.xx | -327.68 | 327.67 | |||
686 | Analog Input 11 Low Setpoint | x.xx | -327.68 | 327.67 | |||
687 | Analog Input 11 Low-Low Setpoint | x.xx | -327.68 | 327.67 | |||
688 | Analog Input 11 Start Delay | x | Seconds | 1 | 32767 | ||
689 | Analog Input 11 Detection Delay | x | Seconds | 1 | 32767 | ||
690 | Analog Input 11 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
691 | Analog Input 11 Restart Delay | x | Minutes | 1 | 32767 | ||
692 | RESERVED | ||||||
693 | RESERVED | ||||||
694 | Analog Input 12 Scale Minimum | x.xx | -327.68 | 327.67 | |||
695 | Analog Input 12 Scale Maximum | x.xx | -327.68 | 327.67 | |||
696 | Analog Input 12 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
697 | Analog Input 12 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
698 | Analog Input 12 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
699 | Analog Input 12 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
700 | Analog Input 12 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
701 | Analog Input 12 High-High Setpoint | x.xx | -327.68 | 327.67 | |||
702 | Analog Input 12 High Setpoint | x.xx | -327.68 | 327.67 | |||
703 | Analog Input 12 Low Setpoint | x.xx | -327.68 | 327.67 | |||
704 | Analog Input 12 Low-Low Setpoint | x.xx | -327.68 | 327.67 | |||
705 | Analog Input 12 Start Delay | x | Seconds | 1 | 32767 | ||
706 | Analog Input 12 Detection Delay | x | Seconds | 1 | 32767 | ||
707 | Analog Input 12 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
708 | Analog Input 12 Restart Delay | x | Minutes | 1 | 32767 | ||
709 | RESERVED | ||||||
710 | RESERVED | ||||||
711 | Analog Input 13 Scale Minimum | x.xx | -327.68 | 327.67 | |||
712 | Analog Input 13 Scale Maximum | x.xx | -327.68 | 327.67 | |||
713 | Analog Input 13 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
714 | Analog Input 13 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
715 | Analog Input 13 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
716 | Analog Input 13 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
717 | Analog Input 13 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
718 | Analog Input 13 High-High Setpoint | x.xx | -327.68 | 327.67 | |||
719 | Analog Input 13 High Setpoint | x.xx | -327.68 | 327.67 | |||
720 | Analog Input 13 Low Setpoint | x.xx | -327.68 | 327.67 | |||
721 | Analog Input 13 Low-Low Setpoint | x.xx | -327.68 | 327.67 | |||
722 | Analog Input 13 Start Delay | x | Seconds | 1 | 32767 | ||
723 | Analog Input 13 Detection Delay | x | Seconds | 1 | 32767 | ||
724 | Analog Input 13 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
725 | Analog Input 13 Restart Delay | x | Minutes | 1 | 32767 | ||
726 | RESERVED | ||||||
727 | RESERVED | ||||||
728 | Analog Input 14 Scale Minimum | x.x | -3276.8 | 3276.7 | |||
729 | Analog Input 14 Scale Maximum | x.x | -3276.8 | 3276.7 | |||
730 | Analog Input 14 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
731 | Analog Input 14 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
732 | Analog Input 14 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
733 | Analog Input 14 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
734 | Analog Input 14 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
735 | Analog Input 14 High-High Setpoint | x.x | -3276.8 | 3276.7 | |||
736 | Analog Input 14 High Setpoint | x.x | -3276.8 | 3276.7 | |||
737 | Analog Input 14 Low Setpoint | x.x | -3276.8 | 3276.7 | |||
738 | Analog Input 14 Low-Low Setpoint | x.x | -3276.8 | 3276.7 | |||
739 | Analog Input 14 Start Delay | x | Seconds | 1 | 32767 | ||
740 | Analog Input 14 Detection Delay | x | Seconds | 1 | 32767 | ||
741 | Analog Input 14 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
742 | Analog Input 14 Restart Delay | x | Minutes | 1 | 32767 | ||
743 | RESERVED | ||||||
744 | RESERVED | ||||||
745 | Analog Input 15 Scale Minimum | x.x | -3276.8 | 3276.7 | |||
746 | Analog Input 15 Scale Maximum | x.x | -3276.8 | 3276.7 | |||
747 | Analog Input 15 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
748 | Analog Input 15 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
749 | Analog Input 15 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
750 | Analog Input 15 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
751 | Analog Input 15 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
752 | Analog Input 15 High-High Setpoint | x.x | -3276.8 | 3276.7 | |||
753 | Analog Input 15 High Setpoint | x.x | -3276.8 | 3276.7 | |||
754 | Analog Input 15 Low Setpoint | x.x | -3276.8 | 3276.7 | |||
755 | Analog Input 15 Low-Low Setpoint | x.x | -3276.8 | 3276.7 | |||
756 | Analog Input 15 Start Delay | x | Seconds | 1 | 32767 | ||
757 | Analog Input 15 Detection Delay | x | Seconds | 1 | 32767 | ||
758 | Analog Input 15 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
759 | Analog Input 15 Restart Delay | x | Minutes | 1 | 32767 | ||
760 | RESERVED | ||||||
761 | RESERVED | ||||||
762 | RESERVED | ||||||
763 | RESERVED | ||||||
764 | RESERVED | ||||||
765 | RESERVED | ||||||
766 | RESERVED | ||||||
767 | RESERVED | ||||||
768 | RESERVED | ||||||
769 | RESERVED | ||||||
770 | RESERVED | ||||||
771 | RESERVED | ||||||
772 | RESERVED | ||||||
773 | RESERVED | ||||||
774 | RESERVED | ||||||
775 | RESERVED | ||||||
776 | RESERVED | ||||||
777 | RESERVED | ||||||
778 | RESERVED | ||||||
779 | RESERVED | ||||||
780 | RESERVED | ||||||
781 | Analog Input 17 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
782 | Analog Input 17 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
783 | Analog Input 17 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
784 | Analog Input 17 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
785 | Analog Input 17 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
786 | Analog Input 17 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
787 | Analog Input 17 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
788 | Analog Input 17 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
789 | Analog Input 17 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
790 | Analog Input 17 Start Delay | x | Seconds | 1 | 32767 | ||
791 | Analog Input 17 Detection Delay | x | Seconds | 1 | 32767 | ||
792 | Analog Input 17 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
793 | Analog Input 17 Restart Delay | x | Minutes | 1 | 32767 | ||
794 | RESERVED | ||||||
795 | RESERVED | ||||||
796 | RESERVED | ||||||
797 | RESERVED | ||||||
798 | Analog Input 18 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
799 | Analog Input 18 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
800 | Analog Input 18 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
801 | Analog Input 18 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
802 | Analog Input 18 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
803 | Analog Input 18 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
804 | Analog Input 18 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
805 | Analog Input 18 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
806 | Analog Input 18 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
807 | Analog Input 18 Start Delay | x | Seconds | 1 | 32767 | ||
808 | Analog Input 18 Detection Delay | x | Seconds | 1 | 32767 | ||
809 | Analog Input 18 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
810 | Analog Input 18 Restart Delay | x | Minutes | 1 | 32767 | ||
811 | RESERVED | ||||||
812 | RESERVED | ||||||
813 | RESERVED | ||||||
814 | RESERVED | ||||||
815 | Analog Input 19 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
816 | Analog Input 19 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
817 | Analog Input 19 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
818 | Analog Input 19 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
819 | Analog Input 19 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
820 | Analog Input 19 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
821 | Analog Input 19 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
822 | Analog Input 19 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
823 | Analog Input 19 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
824 | Analog Input 19 Start Delay | x | Seconds | 1 | 32767 | ||
825 | Analog Input 19 Detection Delay | x | Seconds | 1 | 32767 | ||
826 | Analog Input 19 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
827 | Analog Input 19 Restart Delay | x | Minutes | 1 | 32767 | ||
828 | RESERVED | ||||||
829 | RESERVED | ||||||
830 | RESERVED | ||||||
831 | RESERVED | ||||||
832 | Analog Input 20 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
833 | Analog Input 20 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
834 | Analog Input 20 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
835 | Analog Input 20 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
836 | Analog Input 20 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
837 | Analog Input 20 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
838 | Analog Input 20 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
839 | Analog Input 20 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
840 | Analog Input 20 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
841 | Analog Input 20 Start Delay | x | Seconds | 1 | 32767 | ||
842 | Analog Input 20 Detection Delay | x | Seconds | 1 | 32767 | ||
843 | Analog Input 20 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
844 | Analog Input 20 Restart Delay | x | Minutes | 1 | 32767 | ||
845 | RESERVED | ||||||
846 | RESERVED | ||||||
847 | RESERVED | ||||||
848 | RESERVED | ||||||
849 | Analog Input 21 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
850 | Analog Input 21 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
851 | Analog Input 21 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
852 | Analog Input 21 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
853 | Analog Input 21 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
854 | Analog Input 21 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
855 | Analog Input 21 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
856 | Analog Input 21 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
857 | Analog Input 21 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
858 | Analog Input 21 Start Delay | x | Seconds | 1 | 32767 | ||
859 | Analog Input 21 Detection Delay | x | Seconds | 1 | 32767 | ||
860 | Analog Input 21 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
861 | Analog Input 21 Restart Delay | x | Minutes | 1 | 32767 | ||
862 | RESERVED | ||||||
863 | RESERVED | ||||||
864 | RESERVED | ||||||
865 | RESERVED | ||||||
866 | Analog Input 22 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
867 | Analog Input 22 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
868 | Analog Input 22 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
869 | Analog Input 22 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
870 | Analog Input 22 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
871 | Analog Input 22 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
872 | Analog Input 22 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
873 | Analog Input 22 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
874 | Analog Input 22 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
875 | Analog Input 22 Start Delay | x | Seconds | 1 | 32767 | ||
876 | Analog Input 22 Detection Delay | x | Seconds | 1 | 32767 | ||
877 | Analog Input 22 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
878 | Analog Input 22 Restart Delay | x | Minutes | 1 | 32767 | ||
879 | RESERVED | ||||||
880 | RESERVED | ||||||
881 | RESERVED | ||||||
882 | RESERVED | ||||||
883 | Analog Input 23 Signal-Loss/Broken Fault | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
884 | Analog Input 23 High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
885 | Analog Input 23 High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
886 | Analog Input 23 Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
887 | Analog Input 23 Low-Low Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
888 | Analog Input 23 High-High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
889 | Analog Input 23 High Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
890 | Analog Input 23 Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
891 | Analog Input 23 Low-Low Setpoint | x.x | DegF | -3276.8 | 3276.7 | ||
892 | Analog Input 23 Start Delay | x | Seconds | 1 | 32767 | ||
893 | Analog Input 23 Detection Delay | x | Seconds | 1 | 32767 | ||
894 | Analog Input 23 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
895 | Analog Input 23 Restart Delay | x | Minutes | 1 | 32767 | ||
896 | RESERVED | ||||||
897 | RESERVED | ||||||
898 | Thrust Chamber Oil Temperature Source | x | 1 | 2 |
1 = J-Type Thermocouple (AI10) 2 = RTD (AI16) |
||
899 | Flow Source | x | 1 | 2 |
1 = Analog (AI7) 2 = Calculated |
||
900 | Filter Differential Pressure AI3 Rescale Minimum | x.x | PSI | -3276.8 | 3276.7 | ||
901 | Filter Differential Pressure AI3 Rescale Maximum | x.x | PSI | -3276.8 | 3276.7 | ||
902 | Filter Differential Pressure High-High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
903 | Filter Differential Pressure High Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
904 | Filter Differential Pressure High-High Setpoint | x.x | PSI | -3276.8 | 3276.7 | ||
905 | Filter Differential Pressure High Setpoint | x.x | PSI | -3276.8 | 3276.7 | ||
906 | Filter Differential Pressure Start Delay | x | Seconds | 1 | 32767 | ||
907 | Filter Differential Pressure Detection Delay | x | Seconds | 1 | 32767 | ||
908 | Filter Differential Pressure Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
909 | Filter Differential Pressure Restart Delay | x | Minutes | 1 | 32767 | ||
910 | RESERVED | ||||||
911 | RESERVED | ||||||
912 | Filter Differential Pressure Inlet Analog Input | x | 1 | 5 |
1 = Analog Input 1 2 = Analog Input 3 3 = Analog Input 11 4 = Analog Input 12 5 = Analog Input 13 6 = Analog Input 14 7 = Analog Input 15 |
||
913 | Filter Differential Pressure Outlet Analog Input | x | 1 | 5 |
1 = Analog Input 1 2 = Analog Input 3 3 = Analog Input 11 4 = Analog Input 12 5 = Analog Input 13 6 = Analog Input 14 7 = Analog Input 15 |
||
914 | Unlock Advanced Parameters Analog Inputs | x | 1 | 2 |
1 = Disabled 2 = Enabled |
Feature disabled. | |
915 | Unlock Advanced Parameters Digital Inputs | x | 1 | 2 |
1 = Disabled 2 = Enabled |
Feature disabled. | |
916 | Controller Ethernet IP Address 1 | x | 0 | 255 | 1st octet. | ||
917 | Controller Ethernet IP Address 2 | x | 0 | 255 | 2nd octet. | ||
918 | Controller Ethernet IP Address 3 | x | 0 | 255 | 3rd octet. | ||
919 | Controller Ethernet IP Address 4 | x | 0 | 255 | 4th octet. | ||
920 | Controller Ethernet Subnet Mask 1 | x | 0 | 255 | 1st octet. | ||
921 | Controller Ethernet Subnet Mask 2 | x | 0 | 255 | 2nd octet. | ||
922 | Controller Ethernet Subnet Mask 3 | x | 0 | 255 | 3rd octet. | ||
923 | Controller Ethernet Subnet Mask 4 | x | 0 | 255 | 4th octet. | ||
924 | Controller Ethernet Default Gateway 1 | x | 0 | 255 | 1st octet. | ||
925 | Controller Ethernet Default Gateway 2 | x | 0 | 255 | 2nd octet. | ||
926 | Controller Ethernet Default Gateway 3 | x | 0 | 255 | 3rd octet. | ||
927 | Controller Ethernet Default Gateway 4 | x | 0 | 255 | 4th octet. | ||
928 | Digital Input 1 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
929 | Digital Input 1 Active Delay | x | Seconds | 0 | 32767 | ||
930 | RESERVED | ||||||
931 | RESERVED | ||||||
932 | RESERVED | ||||||
933 | RESERVED | ||||||
934 | RESERVED | ||||||
935 | RESERVED | ||||||
936 | RESERVED | ||||||
937 | Digital Input 2 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
938 | Digital Input 2 Active Delay | x | Seconds | 0 | 32767 | ||
939 | RESERVED | ||||||
940 | RESERVED | ||||||
941 | RESERVED | ||||||
942 | RESERVED | ||||||
943 | RESERVED | ||||||
944 | RESERVED | ||||||
945 | RESERVED | ||||||
946 | Digital Input 3 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
947 | Digital Input 3 Active Delay | x | Seconds | 0 | 32767 | ||
948 | RESERVED | ||||||
949 | RESERVED | ||||||
950 | RESERVED | ||||||
951 | RESERVED | ||||||
952 | RESERVED | ||||||
953 | RESERVED | ||||||
954 | RESERVED | ||||||
955 | Digital Input 4 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
956 | Digital Input 4 Active Delay | x | Seconds | 0 | 32767 | ||
957 | RESERVED | ||||||
958 | RESERVED | ||||||
959 | RESERVED | ||||||
960 | RESERVED | ||||||
961 | RESERVED | ||||||
962 | RESERVED | ||||||
963 | RESERVED | ||||||
964 | Digital Input 5 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
965 | Digital Input 5 Active Delay | x | Seconds | 0 | 32767 | ||
966 | RESERVED | ||||||
967 | RESERVED | ||||||
968 | RESERVED | ||||||
969 | RESERVED | ||||||
970 | RESERVED | ||||||
971 | RESERVED | ||||||
972 | RESERVED | ||||||
973 | Digital Input 6 Confirm When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
974 | Digital Input 6 Confirm Delay | x | Seconds | 0 | 32767 | ||
975 | RESERVED | ||||||
976 | RESERVED | ||||||
977 | RESERVED | ||||||
978 | RESERVED | ||||||
979 | RESERVED | ||||||
980 | RESERVED | ||||||
981 | RESERVED | ||||||
982 | Digital Input 7 Confirm When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
983 | Digital Input 7 Confirm Delay | x | Seconds | 0 | 32767 | ||
984 | RESERVED | ||||||
985 | RESERVED | ||||||
986 | RESERVED | ||||||
987 | RESERVED | ||||||
988 | RESERVED | ||||||
989 | RESERVED | ||||||
990 | RESERVED | ||||||
991 | Digital Input 8 Confirm When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
992 | Digital Input 8 Confirm Delay | x | Seconds | 0 | 32767 | ||
993 | RESERVED | ||||||
994 | RESERVED | ||||||
995 | RESERVED | ||||||
996 | RESERVED | ||||||
997 | RESERVED | ||||||
998 | RESERVED | ||||||
999 | RESERVED | ||||||
1000 | Digital Input 9 Confirm When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1001 | Digital Input 9 Confirm Delay | x | Seconds | 0 | 32767 | ||
1002 | RESERVED | ||||||
1003 | RESERVED | ||||||
1004 | RESERVED | ||||||
1005 | RESERVED | ||||||
1006 | RESERVED | ||||||
1007 | RESERVED | ||||||
1008 | RESERVED | ||||||
1009 | Digital Input 10 Confirm When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1010 | Digital Input 10 Confirm Delay | x | Seconds | 0 | 32767 | ||
1011 | RESERVED | ||||||
1012 | RESERVED | ||||||
1013 | RESERVED | ||||||
1014 | RESERVED | ||||||
1015 | RESERVED | ||||||
1016 | RESERVED | ||||||
1017 | RESERVED | ||||||
1018 | Digital Input 11 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1019 | Digital Input 11 Active Delay | x | Seconds | 0 | 32767 | ||
1020 | Digital Input 11 Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1021 | Digital Input 11 Start Delay | x | Seconds | 1 | 32767 | ||
1022 | Digital Input 11 Detection Delay | x | Seconds | 1 | 32767 | ||
1023 | Digital Input 11 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
1024 | Digital Input 11 Restart Delay | x | Minutes | 1 | 32767 | ||
1025 | RESERVED | ||||||
1026 | RESERVED | ||||||
1027 | Digital Input 12 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1028 | Digital Input 12 Active Delay | x | Seconds | 0 | 32767 | ||
1029 | Digital Input 12 Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1030 | Digital Input 12 Start Delay | x | Seconds | 1 | 32767 | ||
1031 | Digital Input 12 Detection Delay | x | Seconds | 1 | 32767 | ||
1032 | Digital Input 12 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
1033 | Digital Input 12 Restart Delay | x | Minutes | 1 | 32767 | ||
1034 | RESERVED | ||||||
1035 | RESERVED | ||||||
1036 | Digital Input 13 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1037 | Digital Input 13 Active Delay | x | Seconds | 0 | 32767 | ||
1038 | Digital Input 13 Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1039 | Digital Input 13 Start Delay | x | Seconds | 1 | 32767 | ||
1040 | Digital Input 13 Detection Delay | x | Seconds | 1 | 32767 | ||
1041 | Digital Input 13 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
1042 | Digital Input 13 Restart Delay | x | Minutes | 1 | 32767 | ||
1043 | RESERVED | ||||||
1044 | RESERVED | ||||||
1045 | Digital Input 14 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1046 | Digital Input 14 Active Delay | x | Seconds | 0 | 32767 | ||
1047 | Digital Input 14 Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1048 | Digital Input 14 Start Delay | x | Seconds | 1 | 32767 | ||
1049 | Digital Input 14 Detection Delay | x | Seconds | 1 | 32767 | ||
1050 | Digital Input 14 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
1051 | Digital Input 14 Restart Delay | x | Minutes | 1 | 32767 | ||
1052 | RESERVED | ||||||
1053 | RESERVED | ||||||
1054 | Digital Input 15 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1055 | Digital Input 15 Active Delay | x | Seconds | 0 | 32767 | ||
1056 | Digital Input 15 Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1057 | Digital Input 15 Start Delay | x | Seconds | 1 | 32767 | ||
1058 | Digital Input 15 Detection Delay | x | Seconds | 1 | 32767 | ||
1059 | Digital Input 15 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
1060 | Digital Input 15 Restart Delay | x | Minutes | 1 | 32767 | ||
1061 | RESERVED | ||||||
1062 | RESERVED | ||||||
1063 | Digital Input 16 Active When | x | 1 | 2 |
1 = Contact Open 2 = Contact Closed |
||
1064 | Digital Input 16 Active Delay | x | Seconds | 0 | 32767 | ||
1065 | Digital Input 16 Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1066 | Digital Input 16 Start Delay | x | Seconds | 1 | 32767 | ||
1067 | Digital Input 16 Detection Delay | x | Seconds | 1 | 32767 | ||
1068 | Digital Input 16 Restart Type | x | 1 | 2 |
1 = Manual 2 = Timed |
||
1069 | Digital Input 16 Restart Delay | x | Minutes | 1 | 32767 | ||
1070 | RESERVED | ||||||
1071 | RESERVED | ||||||
1072 | Variable Frequency Drive Maximum Speed | x.xx | Hz | 25.00 | 120.00 | ||
1073 | Variable Frequency Drive Base Frequency | x.x | Hz | 25.0 | 120.0 | ||
1074 | Variable Frequency Drive Maximum Voltage | x | Volts | 160 | 500 | ||
1075 | Variable Frequency Drive Acceleration Time | x.x | Seconds | 0 | 3000.0 | ||
1076 | Variable Frequency Drive Deceleration Time | x.x | Seconds | 0 | 3000.0 | ||
1077 | Variable Frequency Drive Torque Boost | x.x | % | 0 | 20.0 | ||
1078 | Variable Frequency Drive Overload | x.x | Amps | 1.0 | 3000.0 | ||
1079 | Variable Frequency Drive Minimum Speed | x.xx | Hz | 0.00 | 120.00 | ||
1080 | Variable Frequency Drive Carrier Frequency | x | kHz | 1 | 10 | ||
1081 | Variable Frequency Drive Control Mode | x | 1 | 2 |
1 = V/Hz 2 = Torque Vector |
||
1082 | Variable Frequency Drive Current Limit | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1083 | Variable Frequency Drive Current Limit Setpoint | x | Amps | 1 | 3000 | ||
1084 | Variable Frequency Drive Stop Mode | x | 1 | 2 |
1 = Decelerate 2 = Coast to Stop |
||
1085 | Variable Frequency Drive Regen Mode | x | 1 | 3 |
1 = Brake/Disabled 2 = Control by Torque 3 = Control by DC Bus |
||
1086 | Variable Frequency Drive Regen Frequency | x.x | Hz | 0 | 120.0 | ||
1087 | Motor Rated Speed | x | RPM | 1 | 4 |
1 = 900 2 = 1200 3 = 1800 4 = 3600 |
|
1088 | Motor Rated Horsepower | x | HP | 1 | 1000 | ||
1089 | Motor Full-Load Amps | x.x | Amps | 1.0 | 3000.0 | ||
1090 | Pressure Control Valve Control Mode | x | 1 | 2 |
1 = Manual Setpoint 2 = Auto Pump Curve |
||
1091 | Pressure Control Valve Manual Setpoint | x | PSI | -32768 | 32767 | ||
1092 | Serial Port 2 VFD Ignore Communication Faults | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1093 | Access Control Operator Password | x | 0 | 9999 | |||
1094 | Access Control Supervisor Password | x | 0 | 9999 | |||
1095 | Main Pump Start/Stop Source | x | 1 | 6 |
1 = Analog Suction Pressure (AI1) 2 = Analog Discharge Pressure (AI2) 3 = Analog Tank Level (AI3) 4 = Maintained Contact Tank Level (DI4) 5 = Momentary Contact Tank Level (DI4/DI5) |
||
1096 | Main Pump Speed Source | x | 1 | 4 |
1 = Analog Suction Pressure (AI1) 2 = Analog Discharge Pressure (AI2) 3 = Analog Tank Level (AI3) 4 = User Manual Entry/Fixed Speed |
||
1097 | Pump Curve Number of Stages | x | 1 | 1000 | |||
1098 | Pump Curve Specific Gravity | x | 0.001 | 2.000 | |||
1099 | Pump Curve 7-Point Point 1 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1100 | Pump Curve 7-Point Point 1 Discharge Pressure | x | PSI | 0 | 32767 | ||
1101 | Pump Curve 7-Point Point 2 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1102 | Pump Curve 7-Point Point 2 Discharge Pressure | x | PSI | 0 | 32767 | ||
1103 | Pump Curve 7-Point Point 3 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1104 | Pump Curve 7-Point Point 3 Discharge Pressure | x | PSI | 0 | 32767 | ||
1105 | Pump Curve 7-Point Point 4 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1106 | Pump Curve 7-Point Point 4 Discharge Pressure | x | PSI | 0 | 32767 | ||
1107 | Pump Curve 7-Point Point 5 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1108 | Pump Curve 7-Point Point 5 Discharge Pressure | x | PSI | 0 | 32767 | ||
1109 | Pump Curve 7-Point Point 6 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1110 | Pump Curve 7-Point Point 6 Discharge Pressure | x | PSI | 0 | 32767 | ||
1111 | Pump Curve 7-Point Point 7 Speed | x.xx | Hz | 0.00 | 120.00 | ||
1112 | Pump Curve 7-Point Point 7 Discharge Pressure | x | PSI | 0 | 32767 | ||
1113 | Pump Curve 7-Point Point 1 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1114 | Pump Curve 7-Point Point 1 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1115 | Pump Curve 7-Point Point 2 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1116 | Pump Curve 7-Point Point 2 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1117 | Pump Curve 7-Point Point 3 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1118 | Pump Curve 7-Point Point 3 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1119 | Pump Curve 7-Point Point 4 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1120 | Pump Curve 7-Point Point 4 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1121 | Pump Curve 7-Point Point 5 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1122 | Pump Curve 7-Point Point 5 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1123 | Pump Curve 7-Point Point 6 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1124 | Pump Curve 7-Point Point 6 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1125 | Pump Curve 7-Point Point 7 Tornado Plot Bounds Lower Pressure | x | PSI | 0 | 32767 | ||
1126 | Pump Curve 7-Point Point 7 Tornado Plot Bounds Upper Pressure | x | PSI | 0 | 32767 | ||
1127 | Support Pumps Charge Pump | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1128 | Support Pumps Charge Pump Pre-Run Time | x | Seconds | 30 | 32767 | ||
1129 | Support Pumps Thrust Chamber Oil Pump | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1130 | Support Pumps Thrust Chamber Oil Pump Pre-Run Time | x | Seconds | 30 | 32767 | ||
1131 | Support Pumps Thrust Chamber Oil Pump Post-Run Time | x | Seconds | 30 | 32767 | ||
1132 | Main Pump Speed (AIx) Proportional Band | x.x | % | -3276.8 | 3276.7 | ||
1133 | Main Pump Speed (Aix) Integral Time | x | Seconds | -32768 | 32767 | ||
1134 | Main Pump Speed (Aix) Derivative Time | x | Seconds | -32768 | 32767 | ||
1135 | Pressure Control Valve Auto Proportional Band | x.x | % | -3276.8 | 3276.7 | ||
1136 | Pressure Control Valve Auto Integral Time | x | Seconds | -32768 | 32767 | ||
1137 | Pressure Control Valve Auto Derivative Time | x | Seconds | -32768 | 32767 | ||
1138 | Pressure Control Valve Travel Time | x | Seconds | 1 | 30000 | ||
1139 | Pressure Control Valve Stabilization Time | x | Seconds | 1 | 30000 | ||
1140 | Pressure Control Valve Start Position | x.x | % | 0.0 | 100.0 | ||
1141 | SD Card Logging Log When | x | 1 | 2 |
1 = Always 2 = Running Only |
||
1142 | SD Card Logging Logging Interval | x | Seconds | 1 | 3600 | ||
1143 | Main Pump User Start | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1144 | Block Valve Control Mode | x | 1 | 2 |
1 = Disabled 2 = Run Sequence |
||
1145 | Block Valve Travel Time | x | Seconds | 1 | 30000 | ||
1146 | (AO1) Pressure Control Valve Position Full Open (100%) | x | 1 | 2 |
1 = 4 mA 2 = 20 mA |
||
1147 | Main Pump Speed Mismatch Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1148 | Pressure Control Valve Out of Curve Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1149 | Pressure Control Valve Failed to Control Pressure Reaction | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Shutdown |
||
1150 | RESERVED | ||||||
1151 | Main Pump Speed OptiMode | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1152 | Pressure Control Valve Position Feedback | x | 1 | 4 |
1 = Disabled 2 = Analog (AI9) 3 = Digital (DI8) 4 = Both (AI9/DI8) |
||
1153 | Pump Curve 7-Point Auto-Bounds Range | x | % | 1 | 100 | ||
1154 | Pump Curve Upper Tolerance | x | % | 0.1 | 100.0 | ||
1155 | Pump Curve Lower Tolerance | x | % | 0.1 | 100.0 | ||
1156 |
Digital Input 16 Function |
x | 1 | 2 | 1 = General Purpose 2 = Reset |
||
1157 | Home Screen | x | 1 | 2 | 1 = Tank 2 = Booster |
||
1158 | Pressure Control Valve Manual Position Setpoint | x.x | % | 0.0 | 100.0 | ||
1159 | Variable Frequency Drive Ethernet IP Address 1 | x | 0 | 255 | 1st octet. | ||
1160 | Variable Frequency Drive Ethernet IP Address 2 | x | 0 | 255 | 2nd octet. | ||
1161 | Variable Frequency Drive Ethernet IP Address 3 | x | 0 | 255 | 3rd octet. | ||
1162 | Variable Frequency Drive Ethernet IP Address 4 | x | 0 | 255 | 4th octet. | ||
1163 | Block Valve Operate When HOA | x | 1 | 2 | 1 = Hand/Auto 2 = Hand/Off/Auto |
||
1164 | Block Valve Operate During Shutdown/Fault | x | 1 | 2 | 1 = Disabled 2 = Enabled |
||
1165 | Block Valve Open Conditions | x | 1 | 2 | 1 = All Met 2 = Any Met |
||
1166 | Block Valve Opened Reaction | x | 1 | 2 | 1 = Disabled 2 = Alarm |
||
1167 | Block Valve Open Source 1 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1168 | Block Valve When To Open 1 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1169 | Block Valve Open Source 2 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1170 | Block Valve When To Open 2 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1171 | Block Valve Open Source 3 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1172 | Block Valve When To Open 3 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1173 | Block Valve Open Source 4 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1174 | Block Valve When To Open 4 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1175 | Block Valve Close Conditions | x | 1 | 2 | 1 = All Met 2 = Any Met |
||
1176 | Block Valve Closed Reaction | x | 1 | 2 | 1 = Disabled 2 = Alarm |
||
1177 | Block Valve Close Source 1 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1178 | Block Valve When To Close 1 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1179 | Block Valve Close Source 2 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1180 | Block Valve When To Close 2 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1181 | Block Valve Close Source 3 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1182 | Block Valve When To Close 3 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1183 | Block Valve Close Source 4 | x | 1 | 10 |
1 = None 11 = Analog Input 15 12 = Digital Input 13 13 = Digital Input 14 14 = Digital Input 15 15 = Digital Input 16 |
||
1184 | Block Valve When To Close 4 | x | 1 | 2 | 1 = Equal or Greater 2 = Equal or Less |
||
1185 | (AO2) Multipurpose Block Valve Position Full Open (100%) | x | 1 | 2 |
1 = 4 mA 2 = 20 mA |
||
1186 | Equipment Stabilization Time | x | Secs | 1 | 60 | ||
1187 | (AO2) Multipurpose Function | x | 1 | 2 |
1 = Block Valve Position 2 = Retransmit Analog Input |
||
1188 | (AO2) Retransmit Analog Input | x | 1 | 23 |
1 = Analog Input 1 2 = Analog Input 2 3 = Analog Input 3 4 = Analog Input 4 5 = Analog Input 5 6 = Analog Input 6 7 = Analog Input 7 8 = Analog Input 8 9 = Analog Input 9 10 = Analog Input 10 11 = Analog Input 11 12 = Analog Input 12 13 = Analog Input 13 14 = Analog Input 14 15 = Analog Input 15 16 = Analog Input 16 17 = Analog Input 17 18 = Analog Input 18 19 = Analog Input 19 20 = Analog Input 20 21 = Analog Input 21 22 = Analog Input 22 23 = Analog Input 23 |
||
1189 | Maintenance Reminder 1 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1190 | Maintenance Reminder 1 Day of Month | x | 1 | 31 | |||
1191 | Maintenance Reminder 2 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1192 | Maintenance Reminder 2 Day of Month | x | 1 | 31 | |||
1193 | Maintenance Reminder 3 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1194 | Maintenance Reminder 3 Day of Month | x | 1 | 31 | |||
1195 | Maintenance Reminder 4 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1196 | Maintenance Reminder 4 Day of Month | x | 1 | 31 | |||
1197 | Maintenance Reminder 5 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1198 | Maintenance Reminder 5 Day of Month | x | 1 | 31 | |||
1199 | Maintenance Reminder 6 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1200 | Maintenance Reminder 6 Day of Month | x | 1 | 31 | |||
1201 | Maintenance Reminder 7 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1202 | Maintenance Reminder 7 Day of Month | x | 1 | 31 | |||
1203 | Maintenance Reminder 8 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1204 | Maintenance Reminder 8 Day of Month | x | 1 | 31 | |||
1205 | Maintenance Reminder 9 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1206 | Maintenance Reminder 9 Day of Month | x | 1 | 31 | |||
1207 | Maintenance Reminder 10 Run-Time Hours | x | Hrs | 1 | 32767 | ||
1208 | Maintenance Reminder 10 Day of Month | x | 1 | 31 | |||
1209 | RESERVED | ||||||
1210 | RESERVED | ||||||
1211 | Analog Input 3 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1212 | Analog Input 4 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1213 | Analog Input 5 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1214 | RESERVED | ||||||
1215 | RESERVED | ||||||
1216 | RESERVED | ||||||
1217 | RESERVED | ||||||
1218 | RESERVED | ||||||
1219 | Analog Input 11 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1220 | Analog Input 12 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1221 | Analog Input 13 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1222 | Analog Input 14 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1223 | Analog Input 15 Tank Status | x | 0 | 7 |
1 = Disabled 2 = Tank 1 3 = Tank 2 4 = Tank 3 5 = Tank 4 6 = Tank 5 7 = Tank 6 |
||
1224 | RESERVED | ||||||
1225 | RESERVED | ||||||
1226 | RESERVED | ||||||
1227 | RESERVED | ||||||
1228 | RESERVED | ||||||
1229 | RESERVED | ||||||
1230 | RESERVED | ||||||
1231 | RESERVED | ||||||
1232 | Support Pumps Charge Pump Post-Run Time | x | Seconds | 30 | 32767 | ||
1233 | VFD Thermal Warning | x | 1 | 3 |
1 = Disabled 2 = Alarm 3 = Alarm & Message |
||
1234 | VFD Thermal Warning Threshold | x | % | 1 | 100 | ||
1235 | Analog Input 8 Flow Totalizer | x | 1 | 2 |
1 = Disabled 2 = Enabled |
||
1250 | Site Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1261 | Analog Input 1 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1272 | Analog Input 1 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1276 | Analog Input 2 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1287 | Analog Input 2 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1291 | Analog Input 3 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1302 | Analog Input 3 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1306 | Analog Input 4 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1317 | Analog Input 4 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1321 | Analog Input 5 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1332 | Analog Input 5 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1336 | Analog Input 6 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1347 | Analog Input 6 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1351 | Analog Input 7 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1362 | Analog Input 7 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1366 | Analog Input 8 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1377 | Analog Input 8 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1381 | Analog Input 9 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1392 | Analog Input 9 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1396 | Analog Input 10/16 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1407 | Analog Input 10/16 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1411 | Analog Input 11 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1422 | Analog Input 11 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1426 | Analog Input 12 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1437 | Analog Input 12 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1441 | Analog Input 13 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1452 | Analog Input 13 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1456 | Analog Input 14 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1467 | Analog Input 14 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1471 | Analog Input 15 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1482 | Analog Input 15 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1501 | Analog Input 17 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1512 | Analog Input 17 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1516 | Analog Input 18 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1527 | Analog Input 18 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1531 | Analog Input 19 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1542 | Analog Input 19 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1546 | Analog Input 20 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1557 | Analog Input 20 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1561 | Analog Input 21 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1572 | Analog Input 21 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1576 | Analog Input 22 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1587 | Analog Input 22 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1591 | Analog Input 23 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1602 | Analog Input 23 Units | x | Chars | 5 | Up to 5 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1606 | Digital Input 1 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1617 | Digital Input 2 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1628 | Digital Input 3 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1639 | Digital Input 4 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1650 | Digital Input 5 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1661 | Digital Input 6 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1672 | Digital Input 7 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1683 | Digital Input 8 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1694 | Digital Input 9 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1705 | Digital Input 10 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1716 | Digital Input 11 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1727 | Digital Input 12 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1738 | Digital Input 13 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1749 | Digital Input 14 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1760 | Digital Input 15 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. | ||
1771 | Digital Input 16 Name | x | Chars | 20 | Up to 20 ASCII characters. 2 characters per 16-bit register. Be sure to include null terminator. |
Parameters (32-Bit Holding Registers) – Read/Write
Address | Description | Scaling | Units | Minimum | Maximum | Values | Notes |
28722 | Analog Input 7 Scale Minimum | x | BPD | -999999 | 999999 | ||
28723 | Analog Input 7 Scale Maximum | x | BPD | -999999 | 999999 | ||
28724 | Analog Input 7 High-High Setpoint | x | BPD | -999999 | 999999 | ||
28725 | Analog Input 7 High Setpoint | x | BPD | -999999 | 999999 | ||
28726 | Analog Input 7 Low Setpoint | x | BPD | -999999 | 999999 | ||
28727 | Analog Input 7 Low-Low Setpoint | x | BPD | -999999 | 999999 | ||
28728 | Analog Input 8 Scale Minimum | x | -999999 | 999999 | |||
28729 | Analog Input 8 Scale Maximum | x | -999999 | 999999 | |||
28730 | Analog Input 8 High-High Setpoint | x | -999999 | 999999 | |||
28731 | Analog Input 8 High Setpoint | x | -999999 | 999999 | |||
28732 | Analog Input 8 Low Setpoint | x | -999999 | 999999 | |||
28733 | Analog Input 8 Low-Low Setpoint | x | -999999 | 999999 | |||
28734 | Main Pump Start/Stop Start Setpoint | x.x | -214748364.8 | 214748364.8 | |||
28735 | Main Pump Start/Stop Stop Setpoint | x.x | -214748364.8 | 214748364.8 | |||
28736 | Main Pump Speed Maintain Setpoint | x.x | -214748364.8 | 214748364.8 | |||
28737 | Main Pump Speed Fixed Speed | x.xx | Hz | 0.00 | 120.00 | ||
28738 | Pump Curve 7-Point Point 1 Flow | x | BPD | 0 | 999999 | ||
28739 | Pump Curve 7-Point Point 2 Flow | x | BPD | 0 | 999999 | ||
28740 | Pump Curve 7-Point Point 3 Flow | x | BPD | 0 | 999999 | ||
28741 | Pump Curve 7-Point Point 4 Flow | x | BPD | 0 | 999999 | ||
28742 | Pump Curve 7-Point Point 5 Flow | x | BPD | 0 | 999999 | ||
28743 | Pump Curve 7-Point Point 6 Flow | x | BPD | 0 | 999999 | ||
28744 | Pump Curve 7-Point Point 7 Flow | x | BPD | 0 | 999999 | ||
28745 | Pump Curve 7-Point Point 1 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28746 | Pump Curve 7-Point Point 1 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28747 | Pump Curve 7-Point Point 2 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28748 | Pump Curve 7-Point Point 2 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28749 | Pump Curve 7-Point Point 3 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28750 | Pump Curve 7-Point Point 3 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28751 | Pump Curve 7-Point Point 4 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28752 | Pump Curve 7-Point Point 4 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28753 | Pump Curve 7-Point Point 5 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28754 | Pump Curve 7-Point Point 5 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28755 | Pump Curve 7-Point Point 6 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28756 | Pump Curve 7-Point Point 6 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28757 | Pump Curve 7-Point Point 7 Tornado Plot Bounds Lower Flow | x | BPD | 0 | 999999 | ||
28758 | Pump Curve 7-Point Point 7 Tornado Plot Bounds Upper Flow | x | BPD | 0 | 999999 | ||
28759 | Block Valve Open Setpoint 1 | x.x | -214748364.8 | 214748364.8 | |||
28760 | Block Valve Open Setpoint 2 | x.x | -214748364.8 | 214748364.8 | |||
28761 | Block Valve Open Setpoint 3 | x.x | -214748364.8 | 214748364.8 | |||
28762 | Block Valve Open Setpoint 4 | x.x | -214748364.8 | 214748364.8 | |||
28763 | Block Valve Close Setpoint 1 | x.x | -214748364.8 | 214748364.8 | |||
28764 | Block Valve Close Setpoint 2 | x.x | -214748364.8 | 214748364.8 | |||
28765 | Block Valve Close Setpoint 3 | x.x | -214748364.8 | 214748364.8 | |||
28766 | Block Valve Close Setpoint 4 | x.x | -214748364.8 | 214748364.8 |
Parameters (Bits/Coils) – Read/Write
Address | Description | Notes |
160 | Maintenance Reminder 1 Reset |
Resets Maintenance Reminder 1. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
161 | Maintenance Reminder 2 Reset |
Resets Maintenance Reminder 2. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
162 | Maintenance Reminder 3 Reset |
Resets Maintenance Reminder 3. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
163 | Maintenance Reminder 4 Reset |
Resets Maintenance Reminder 4. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
164 | Maintenance Reminder 5 Reset |
Resets Maintenance Reminder 5. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
165 | Maintenance Reminder 6 Reset |
Resets Maintenance Reminder 6. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
166 | Maintenance Reminder 7 Reset |
Resets Maintenance Reminder 7. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
167 | Maintenance Reminder 8 Reset |
Resets Maintenance Reminder 8. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
168 | Maintenance Reminder 9 Reset |
Resets Maintenance Reminder 9. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
169 | Maintenance Reminder 10 Reset |
Resets Maintenance Reminder 10. If Maintenance Reminder 1 Frequency set to Run-Time, will reset the countdown Timer, even if the reminder is not active. |
500 | Trends Plot Curve 1 None |
Selects data for plotting as Curve 1 on Trends screen. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
501 | Trends Plot Curve 1 Speed | |
502 | Trends Plot Curve 1 Voltage | |
503 | Trends Plot Curve 1 Current | |
504 | Trends Plot Curve 1 Torque | |
505 | Trends Plot Curve 1 Horsepower | |
506 | Trends Plot Curve 1 Analog Input 1 | |
507 | Trends Plot Curve 1 Analog Input 2 | |
508 | Trends Plot Curve 1 Analog Input 4 | |
509 | Trends Plot Curve 1 Analog Input 5 | |
510 | Trends Plot Curve 2 None |
Selects data for plotting as Curve 2 on Trends screen. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
511 | Trends Plot Curve 2 Speed | |
512 | Trends Plot Curve 2 Voltage | |
513 | Trends Plot Curve 2 Current | |
514 | Trends Plot Curve 2 Torque | |
515 | Trends Plot Curve 2 Horsepower | |
516 | Trends Plot Curve 2 Analog Input 1 | |
517 | Trends Plot Curve 2 Analog Input 2 | |
518 | Trends Plot Curve 2 Analog Input 4 | |
519 | Trends Plot Curve 2 Analog Input 5 | |
520 | Trends Plot Curve 3 None |
Selects data for plotting as Curve 3 on Trends screen. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
521 | Trends Plot Curve 3 Analog Input 3 | |
522 | Trends Plot Curve 3 Analog Input 7 | |
523 | Trends Plot Curve 3 Analog Input 8 | |
524 | Trends Plot Curve 3 Analog Input 9 | |
525 | Trends Plot Curve 3 Analog Input 10/16 | |
526 | Trends Plot Curve 3 Analog Input 14 | |
527 | Trends Plot Curve 3 Analog Input 15 | |
528 | Trends Plot Curve 3 Analog Input 17 | |
529 | Trends Plot Curve 3 Analog Input 18 | |
530 | Trends Plot Curve 3 Analog Input 19 | |
531 | Trends Plot Curve 3 Analog Input 20 | |
532 | Trends Plot Curve 3 Analog Input 21 | |
533 | Trends Plot Curve 3 Analog Input 22 | |
534 | Trends Plot Curve 3 Analog Input 23 | |
535 | RESERVED | |
536 | Trends Plot Curve 4 None |
Selects data for plotting as Curve 4 on Trends screen. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
537 | Trends Plot Curve 4 Analog Input 3 | |
538 | Trends Plot Curve 4 Analog Input 7 | |
539 | Trends Plot Curve 4 Analog Input 8 | |
540 | Trends Plot Curve 4 Analog Input 9 | |
541 | Trends Plot Curve 4 Analog Input 10/16 | |
542 | Trends Plot Curve 4 Analog Input 14 | |
543 | Trends Plot Curve 4 Analog Input 15 | |
544 | Trends Plot Curve 4 Analog Input 17 | |
545 | Trends Plot Curve 4 Analog Input 18 | |
546 | Trends Plot Curve 4 Analog Input 19 | |
547 | Trends Plot Curve 4 Analog Input 20 | |
548 | Trends Plot Curve 4 Analog Input 21 | |
549 | Trends Plot Curve 4 Analog Input 22 | |
550 | Trends Plot Curve 4 Analog Input 23 | |
551 | RESERVED | |
552 | Trends Plot Curve 5 None |
Selects data for plotting as Curve 5 on Trends screen. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
553 | Trends Plot Curve 5 Analog Input 6 | |
554 | Trends Plot Curve 5 Analog Input 11 | |
555 | Trends Plot Curve 5 Analog Input 12 | |
556 | Trends Plot Curve 5 Analog Input 13 | |
557 | RESERVED | |
558 | RESERVED | |
559 | RESERVED | |
560 | RESERVED | |
561 | RESERVED | |
562 | RESERVED | |
563 | RESERVED | |
564 | RESERVED | |
565 | RESERVED | |
566 | RESERVED | |
567 | RESERVED | |
568 | Trends Plot Curve 6 None |
Selects data for plotting as Curve 6 on Trends screen. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
569 | Trends Plot Curve 6 Analog Input 6 | |
570 | Trends Plot Curve 6 Analog Input 11 | |
571 | Trends Plot Curve 6 Analog Input 12 | |
572 | Trends Plot Curve 6 Analog Input 13 | |
573 | RESERVED |
Selects the pump curve profile type. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
574 | Pump Curve Profile Type Custom Coefficients | |
575 | Pump Curve Profile Type Custom 7-Point | |
576 | RESERVED |
RESERVED. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
577 | RESERVED | |
578 | RESERVED | |
579 | RESERVED | |
580 | RESERVED | |
581 | RESERVED | |
582 | RESERVED | |
583 | RESERVED | |
584 | RESERVED | |
585 | RESERVED | |
586 | RESERVED | |
587 | RESERVED | |
588 | RESERVED | |
589 | RESERVED | |
590 | RESERVED | |
591 | RESERVED | |
592 | RESERVED | |
600 | Pressure Control Valve Control Mode Auto Pump Curve |
Selects the pressure control valve control mode. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
601 | Pressure Control Valve Control Mode Manual Pressure | |
602 | Pressure Control Valve Control Mode Manual Position | |
610 | Maintenance Reminder 1 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
611 | Maintenance Reminder 1 Frequency Run-Time | |
612 | Maintenance Reminder 1 Frequency Monthly | |
613 | Maintenance Reminder 1 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
614 | Maintenance Reminder 1 Run-Time Source Main Pump | |
615 | Maintenance Reminder 1 Run-Time Source Charge Pump | |
616 | Maintenance Reminder 1 Run-Time Source Thrst Chmbr Oil Pump | |
617 | Maintenance Reminder 2 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
618 | Maintenance Reminder 2 Frequency Run-Time | |
619 | Maintenance Reminder 2 Frequency Monthly | |
620 | Maintenance Reminder 2 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
621 | Maintenance Reminder 2 Run-Time Source Main Pump | |
622 | Maintenance Reminder 2 Run-Time Source Charge Pump | |
623 | Maintenance Reminder 2 Run-Time Source Thrst Chmbr Oil Pump | |
624 | Maintenance Reminder 3 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
625 | Maintenance Reminder 3 Frequency Run-Time | |
626 | Maintenance Reminder 3 Frequency Monthly | |
627 | Maintenance Reminder 3 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
628 | Maintenance Reminder 3 Run-Time Source Main Pump | |
629 | Maintenance Reminder 3 Run-Time Source Charge Pump | |
630 | Maintenance Reminder 3 Run-Time Source Thrst Chmbr Oil Pump | |
631 | Maintenance Reminder 4 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
632 | Maintenance Reminder 4 Frequency Run-Time | |
633 | Maintenance Reminder 4 Frequency Monthly | |
634 | Maintenance Reminder 4 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
635 | Maintenance Reminder 4 Run-Time Source Main Pump | |
636 | Maintenance Reminder 4 Run-Time Source Charge Pump | |
637 | Maintenance Reminder 4 Run-Time Source Thrst Chmbr Oil Pump | |
638 | Maintenance Reminder 5 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
639 | Maintenance Reminder 5 Frequency Run-Time | |
640 | Maintenance Reminder 5 Frequency Monthly | |
641 | Maintenance Reminder 5 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
642 | Maintenance Reminder 5 Run-Time Source Main Pump | |
643 | Maintenance Reminder 5 Run-Time Source Charge Pump | |
644 | Maintenance Reminder 5 Run-Time Source Thrst Chmbr Oil Pump | |
645 | Maintenance Reminder 6 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
646 | Maintenance Reminder 6 Frequency Run-Time | |
647 | Maintenance Reminder 6 Frequency Monthly | |
648 | Maintenance Reminder 6 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
649 | Maintenance Reminder 6 Run-Time Source Main Pump | |
650 | Maintenance Reminder 6 Run-Time Source Charge Pump | |
651 | Maintenance Reminder 6 Run-Time Source Thrst Chmbr Oil Pump | |
652 | Maintenance Reminder 7 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
653 | Maintenance Reminder 7 Frequency Run-Time | |
654 | Maintenance Reminder 7 Frequency Monthly | |
655 | Maintenance Reminder 7 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
656 | Maintenance Reminder 7 Run-Time Source Main Pump | |
657 | Maintenance Reminder 7 Run-Time Source Charge Pump | |
658 | Maintenance Reminder 7 Run-Time Source Thrst Chmbr Oil Pump | |
659 | Maintenance Reminder 8 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
660 | Maintenance Reminder 8 Frequency Run-Time | |
661 | Maintenance Reminder 8 Frequency Monthly | |
662 | Maintenance Reminder 8 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
663 | Maintenance Reminder 8 Run-Time Source Main Pump | |
664 | Maintenance Reminder 8 Run-Time Source Charge Pump | |
665 | Maintenance Reminder 8 Run-Time Source Thrst Chmbr Oil Pump | |
666 | Maintenance Reminder 9 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
667 | Maintenance Reminder 9 Frequency Run-Time | |
668 | Maintenance Reminder 9 Frequency Monthly | |
669 | Maintenance Reminder 9 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
670 | Maintenance Reminder 9 Run-Time Source Main Pump | |
671 | Maintenance Reminder 9 Run-Time Source Charge Pump | |
672 | Maintenance Reminder 9 Run-Time Source Thrst Chmbr Oil Pump | |
673 | Maintenance Reminder 10 Frequency Disabled |
Selects the maintenance reminder frequency. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
674 | Maintenance Reminder 10 Frequency Run-Time | |
675 | Maintenance Reminder 10 Frequency Monthly | |
676 | Maintenance Reminder 10 Run-Time Source Panel |
Selects the maintenance reminder run-time source. Only one bit may be Set at a time. Setting a bit will Reset any other Set bit. |
677 | Maintenance Reminder 10 Run-Time Source Main Pump | |
678 | Maintenance Reminder 10 Run-Time Source Charge Pump | |
679 | Maintenance Reminder 10 Run-Time Source Thrst Chmbr Oil Pump |
Parameters (32-Bit Floating Point Holding Registers) – Read/Write
Address | Description | Units | Minimum | Maximum | Values | Notes |
16434 | Pump Curve Custom Coefficients Plot Minimum Flow | BPD | ||||
16435 | Pump Curve Custom Coefficients Plot Maximum Flow | BPD | ||||
16436 | Pump Curve Custom Coefficients BEP Flow @ 60 Hz | BPD | ||||
16437 | Pump Curve Custom Coefficients BEP Minimum Flow @ 60 Hz | BPD | ||||
16438 | Pump Curve Custom Coefficients BEP Maximum Flow @ 60 Hz | BPD | ||||
16439 | Pump Curve Custom Coefficients Coefficient X^5 (a) | |||||
16440 | Pump Curve Custom Coefficients Coefficient X^4 (b) | |||||
16441 | Pump Curve Custom Coefficients Coefficient X^3 (c) | |||||
16442 | Pump Curve Custom Coefficients Coefficient X^2 (d) | |||||
16443 | Pump Curve Custom Coefficients Coefficient X^1 (e) | |||||
16444 | Pump Curve Custom Coefficients Coefficient X^0 (f) |
Comments
0 comments
Article is closed for comments.